Thales MissionLINK Certus 200 Скачать руководство пользователя | Manualshive

Страница: 45 / 61

background image

3-1

Installation Guide 84465 Rev. H

TROUBLESHOOTING

Troubleshooting

Table 3-1 Troubleshooting

PROBLEM

SOLUTION

Satellite LED Flashing

GREEN



Flashing GREEN light indicates that it is acquiring the
satellite. If it continues to flash for more than 5 minutes,
check that the antenna has a clear view of the sky.



Reboot TU.

Satellite LED Flashing

RED



Critical Fault Detected. Open Management Portal

http://portal.thaleslink

(or

https://portal.thaleslink

and check

Alerts. Make any adjustments. (For example: check antenna
connection, or GPS not acquired.)



Turn unit off and on again. If same result, contact your
service provider.

System LED Flashing

Green



Start-up in progress. Wait until unit has run diagnostics and
completed start procedure. This may take more time than
usual when acquiring satellites for the first time



Switch power off and back on if the light doesn’t turn solid
green after 5 minutes.

System LED Flashing

RED

Fault Detected. Open Management Portal

http://portal.thaleslink

(or

https://portal.thaleslink

and check for alerts. Make any

adjustments. (For example: Common alerts include, but not
limited to, are the SIM Card not installed, SIM Card not
provisioned. Power-Up Test (POST) failure.)



Turn unit off and on again. If same result, contact your
service provider.

Wi-Fi LED

OFF – Turn Wi-Fi ON using the Management Portal through a
hardwired, PoE connection.
ThalesLINK > Settings > Wi-Fi

Solid RED – Wi-Fi may need to turned off and back on again
from the Management Portal. If the LED does not turn to
GREEN within a minute, reboot the TU.

Flashing GREEN – If this continues for more than a minute or
two, check for NO OR WEAK Wi-Fi

Call Logs are not
appearing

Call logs must be enabled. Verify call logs are enabled
(SETTING



PHONE



PHONE CONFIGURATION)

«
...
43
44
45
46
47
...
»

Содержание MissionLINK Certus 200






























































Отзывы:

Нет отзывов

Похожие инструкции для MissionLINK Certus 200

Бренд: ABB Страницы: 11

Бренд: Labnet Страницы: 5

SafetuNet Alert

Бренд: Masimo Страницы: 2

Бренд: QBC Diagnostics Страницы: 65

Бренд: T-Rex Страницы: 13

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: MAGIC FX Страницы: 25

FlexDraper FD2 Series

Бренд: MacDon Страницы: 2

OXYGEN PRO MINI

Бренд: M-Audio Страницы: 56

Бренд: Valcom Страницы: 6

Бренд: Vaisala Страницы: 60

Бренд: Yamaha Страницы: 48

Бренд: Yamaha Страницы: 85

Бренд: Yamaha Страницы: 43

Бренд: Yamaha Страницы: 200

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды