background image

©Copyright Task Force Tips LLC 2021

8

LIY-350 January 13, 2021 Rev00

4.0 INSTALLATION

4.1 STRUCTURAL REQUIREMENTS

The structure that the monitor is mounted to must withstand the internal pressure of the monitor as well as shear and bending forces due

to nozzle reaction. Nozzle reaction can be as high as 1100 lbs (500 kg)(1500 gpm at 200 psi).
For flanged connections, the use of flat flanges without raised faces is recommended. Use a ring gasket as defined in ASME 16.21 or

ISO 7483. Tighten flange bolts in an alternating sequence as shown below. Tighten sequentially each bolt or stud three times to 30%,

then 60%, and finally 100% of the specified torque. Tighten to a total of 76-80 ft-lb (100-110 N·m).

Figure 4.1

Table 4.1

WARNING

Reaction forces generated by master stream flows are capable of causing injury and property

damage if not properly supported. Monitors should be securely installed by qualified individuals.

• Mounting objects must be capable of withstanding maximum nozzle reaction force listed in 

SPECIFICATIONS.

• The monitor must be securely mounted to rigid support members.

• Do not use flanges or pipe made from plastic for monitor mounting.

• Torque all fasteners to specified values. 

FLANGE TYPE

OPTION #

OUTSIDE 

DIAMETER

THICKNESS

BOLT HOLE 

CIRCLE

# OF 

BOLTS

SIZE OF 

BOLTS

in

mm

in

mm

in

mm

in

mm

3” ANSI 125/150-DN80 PN20

1

7.5

190

0.75

20

6.0

152.5

4

5/8

16

4” ANSI 150-DN100 PN20

2

9.0

230

0.94

23

7.5

190

8

5/8

16

1

3

2

4

1

5

3

7

2

6

4

8

Tighten Sequentially Each Bolt Three Times to a Total of 76-80 ft-lb (100-110 N·m)

Содержание RADIUS Series

























Отзывы: