background image

9

Nose Assemblies

Nose assemblies should be serviced at weekly intervals. You should hold  some stock of all  internal components of the nose assembly and
nose tips as they will need regular replacement.

Remove the nose equipment using the reverse procedure to the ‘Fitting instructions’.

Any worn or damaged part should be replaced.

Clean and check wear on jaws.

Ensure that the jaw spreader is not distorted.

Check spring is not distorted.

Assemble according to fitting instructions above.

* Item included in the G2 service kit. For complete list see page 17.

F I T T I N G   I N S T R U C T I O N S

I M P O R T A N T

The air supply must be disconnected when fitting or removing nose assemblies.

Item numbers in bold refer to nose assembly components in all 3 nose tip tables.

Lightly coat jaws with Moly lithium grease*.

Drop jaws into jaw housing 3.

Insert jaw spreader into jaw housing 3.

Locate buffer on jaw spreader 5.

Locate spring onto jaw spreader 5.

Fit locking ring onto the jaw spreader housing of the tool.

Holding tool pointing down, screw the assembled jaw housing onto the jaw spreader housing and tighten with spanner. 

Screw the nose tip into nose casing and tighten with spanner*.

Place nose casing over jaw housing and screw onto the tool, tightening with spanner*.

S E R V I C I N G   I N S T R U C T I O N S

Содержание Genesis G2




























Отзывы: