background image

3

Contents

Safety Rules

4

Tool Specifications
Tool Dimensions

5

Intent of Use
Range of Fasteners

6

Part Numbering

6

Putting into Service
Air Supply

7

Operating Procedure

7

Adjusting the Vacuum Extraction

7

Nose Assemblies
Selection of Nose Tips

8&10

Fitting and Servicing Instructions

9

Accessories
Stem Deflector

11

Extension

11

Side Ejector

11

Stem Collector

11

Swivel Heads

12

Preparing the Base Tool

13

Swivel Head Fitting Instructions

14

Swivel Head Servicing Instructions

15

Servicing the Tool
Daily / Weekly

16

Moly Lithium Grease EP 3753 Safety Data

16

Service Kit

17

Annually

18

Head Assembly

18

Pneumatic Piston Assembly

19

Valve Spool Assembly

19

Trigger

19

General Assembly of Base Tool
General Assembly and Parts List

20-21

Priming
Oil Details

22

Hyspin VG 32 Oil Safety Data

22

Priming Kit

22

Priming Procedure

23

Fault Diagnosis
Symptom, Possible Cause & Remedy

24

Textron Fastening Systems policy is one of continuous product development and improvement and we reserve the right to change the specification of any product without prior notice.

Warranty
Textron Fastening Systems installation tools carry a 12 month warranty against defects
caused by faulty materials or workmanship, the warranty period commencing from the
date of delivery confirmed by invoice or delivery note.

The warranty applies to the user/purchaser when sold through an authorised outlet,
and only when used for the intended purpose. The warranty is invalidated if the
installation tool is not serviced, maintained and operated according to the instructions
contained in the Instruction and Service Manuals.

In the event of a defect or failure, and at its sole discretion, Textron Fastening Systems
undertakes only to repair or replace faulty components.

C O N T E N T S

Содержание Genesis G2




























Отзывы: