TEXIO DL-2060 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 152

TEXIO DL-2060 Скачать руководство пользователя страница 7

1

1

Overview

This chapter will give you an overview of DL-2060’s basic features and guide you through
the basics of DL-2060 digital multimeter. Users will become familiar with those features
after reading this chapter.

1.1 Setting up Your DL-2060 Digital Multimeter

The purpose of this section is to prepare users for using DL-2060 DMM. You may want to
check if you have all the parts with your multimeter. All our products are handled and
inspected professionally before shipping out to our customers. If you find any damaged
or missing parts, please contact your local service representative immediately and do
not attempt to operate the damaged product.

1.1.1 Inspection

Your product package is supplied with the following items:

Power line cord :1

Standard Test Leads : 1

CD : 1

（

User's Manual and software

）

USB cable

:

1

Test Lead Ratings:

Material:

IEC 61010-031 CAT III
Operating Voltage: 1000V DC
Current: 10 Ampers
UL/CE Rated

Probe Body: Outer Insulation-Santoprene Rubber.
Banana  Plug:  Body  Brass,  Nickel  Plated  Spring  Beryllium
Copper,Nickel Plated.
Insulation:  Polypropylene  Resin  Flasme  Retardant  Grade
2038.

If any part of the Test Lead Set is damaged, please do not use and replace with a new set.

If users use the Test Lead Set without following the specification of
DL-2060, the protection of the Test Lead Set could be impaired. In
addition, please don’t use a damaged Test Lead Set against the
instrument break or personal injury.

WARNING

!

«
...
5
6
7
8
9
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов