TEXIO DL-2060 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 152

TEXIO DL-2060 Скачать руководство пользователя страница 61

55

Figure 4-13

Remote Interface Operation

You can also use the remote interface operations from your PC terminal to set the trigger
delay. To select a delay time, use the following command or set the trigger delay to be
automatic:

TRIGger:DELay {<seconds>|MINimum|MAXimum}

or

TRIGger:DELay:AUTO {OFF|ON}

3.3 Math Operations

This section will introduce the mathematical operations in DL-2060. There are eight
math operations: RITIO, %, Min/Max, NULL, Limits, MX+B, dB and dBm testing. They
either store data for later use or perform mathematical operations on the readings. Note
that these math operations are available to all measurement functions except continuity
and diode testing.

※

Note: The “MATH” anunnciator on the display indicates the state of a mathematical

feature, excluding Ratio, and will be lit by enabling whichever math feature. Also, press
the same buttons again for the enabled math feature will disable the same math feature.

※

Note: Press RATIO button, the “RATIO” anunnciator will be lit on the display.

«
...
59
60
61
62
63
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов