TEXIO DL-2060 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 152

TEXIO DL-2060 Скачать руководство пользователя страница 49

43

SENSe:VOLTage:DC:NPLCycles? [MINimum|MAXimum]
SENSe:CURRent:DC:NPLCycles {0.02|0.1|1|10|MINimum|MAXimum}
SENSe:CURRent:DC:NPLCycles? [MINimum|MAXimum]
SENSe:RESistance:NPLCycles {0.02|0.1|1|10|MINimum|MAXimum}
SENSe:RESistance:NPLCycles? [MINimum|MAXimum]
SENSe:FRESistance:NPLCycles {0.02|0.1|1|10|MINimum|MAXimum}
SENSe:FRESistance:NPLCycles? [MINimum|MAXimum]

For frequency and period measurements, aperture time (or gate time) is analogous to
integration time, and you can use the following commands to set it. Specify 10 ms (4 1/2
digits), 100 ms (default; 5 1/2 digits), or 1 second (6 1/2 digits).

SENSe:FREQuency:APERture {0.01|0.1|1|MINimum|MAXimum}
SENSe:FREQuency:APERture? [MINimum|MAXimum]
SENSe:PERiod:APERture {0.01|0.1|1|MINimum|MAXimum}
SENSe:PERiod:APERture? [MINimum|MAXimum]

3.1.8 Sensor Selection for Temperature Measurements

The multimeter supports both thermocouple and RTD. User needs to configure the
multimeter for the right sensor type before they can make temperature measurements.

RTD

Definition

If you are using RTD, the options are: PT100, D100, F100, PT385, PT3916, user-defined
RTD, NTCT and SPRTD. If you need to change the factors that are used to calculate the
temperature in RTD, choose user-defined RTD in which you are able to change any
factors as you wish. The default factors used are listed in

Table 4-3

:

Table 4-3

Type

Alpha

Beta

Delta

R-zero

PT100

0.003850

0.10863

1.49990

100Ω

D100

0.003920

0.10630

1.49710

100Ω

F100

0.003900

0.11000

1.49589

100Ω

PT385

0.003850

0.11100

1.50700

100Ω

PT3916

0.003916

0.11600

1.50594

100Ω

NTCT

0.003850

0.10863

1.49990

100Ω

Here is the temperature equation that is used to determine the RTD temperature:

«
...
47
48
49
50
51
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов