manualshive.com logo in svg

TEXIO DL-2060, Инструкция по эксплуатации, Страница: 34 / 152

Поделиться
Скачать
TEXIO DL-2060 Скачать руководство пользователя страница 34

 

 

28 

2.7    Temperature Measurements 

The DL-2060 supports thermocouples and resistance temperature detector (RTD) types 
of probes. For thermocouples, DL-2060 supports 7 types: E, J, K, N, R, S and T. Please 
refer to 

Table 3-1 

for their temperature ranges. Be sure that the temperature function 

is configured for the right sensor type before making measurements (Refer to 3.1.8 for 
how to make the sensor configuration). 
 
In general, RTDs have a better accuracy and long-term stability than thermocouples. 
The default RTD type in DL-2060 is PT100 and the thermocouple is type K. 

 

Table 3-1 

Sensor Type 

Temperature 

Range(°C) 

Temperature 

Range(°F) 

E 

-270 to

 

1000 

-518 to

 

1832 

J 

-210 to

 

1200 

-140 to

 

2192 

K 

-270 to

 

1372 

-518 to

 

2502 

N 

-270 to

 

1300 

-518 to

 

2372 

R 

-50 to

 

1768 

-122 to

 

3236 

S 

-50 to

 

1768 

-122 to

 

3236 

T 

-270 to

 

400 

-518 to

 

752 

RTD (PT 100) 

-200 to

 

850 

-392 to

 

1562 

 
 

2.7.1    Thermocouple Measurements 

Connect the thermocouple adapter (TA-65 option: only for K-type) to the banana jacks 
on the front panel. The difference between each type is subject to the patch thermal 
leads. 

※ 

Note:Only connection via the front panel can be used for temperature measurements. 

 

How to measure thermocouple 

 

①

 

Use terminals switch to select terminals on the front panel. 

②

 

To measure thermocouple must be via thermocouple adapter and the low thermal 
patch  leads  as  shown  in 

Figure

 

3-12

.  (When  the  mentioned  modules  are  well 

connected as the following figure, please go to the next step.) 

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов