TEXIO DL-2060 Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 152

TEXIO DL-2060 Скачать руководство пользователя страница 132

126

*SRE?

Query the Status Byte enable register. The multimeter returns a decimal value which corresponds
to the binary-weighted sum of all bits set in the register.

*STB?

Query the Status Byte summary register. The *STB? command is similar to a serial poll but it is
processed like any other instrument command. The *STB? command returns the same result as
a serial poll but the “request service” bit (bit 6) is not cleared if a serial poll has occurred.

B.10 SCPI Compliance Information

This  section  encloses  a  list  of  commands  that  are  device-specific  to  the  DL-2060.
Although not included in the 1999.0 version of the SCPI standard, these commands are
designed with the SCPI format in mind and they follow all of the syntax rules of the
standard.

Many  of  the  required  SCPI  commands  are  accepted  by  the  multimeter  but  are  not
described  in  this  manual  for  simplicity  or  clarity.  Most  of  these  non-documented
commands duplicate the functionality of a command already described in this chapter.

MEASure:

CONTinuity?
DIODe?

SAMPle:

COUNt {<

value

>|MINimum|MAXimum}

COUNt? [MINimum|MAXimum]

[SENSe:]

FUNCtion "CONTinuity"
FUNCtion "DIODe"
FREQuency:VOLTage:RANGe {<

range

>|MINimum|MAXimum}

FREQuency:VOLTage:RANGe? [MINimum|MAXimum]
FREQuency:VOLTage:RANGe:AUTO {OFF|ON}
FREQuency:VOLTage:RANGe:AUTO?
PERiod:VOLTage:RANGe {<

range

>|MINimum|MAXimum}

PERiod:VOLTage:RANGe? [MINimum|MAXimum]
PERiod:VOLTage:RANGe:AUTO {OFF|ON}
PERiod:VOLTage:RANGe:AUTO?
ZERO:AUTO?

«
...
130
131
132
133
134
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов