TEXIO DL-2060 Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 152

TEXIO DL-2060 Скачать руководство пользователя страница 125

119

ROUTe:SCAN:SCAN

Run SCAN mode

ROUTe:SCAN:STEP

Run STEP mode

B.6 The Math Operation Command

CALCulate:FUNCtion {PERCent|AVERage|NULL|LIMit|MXB|DB|DBM}

Select the math function. Only one function can be enabled at a time. The default function is
percent.

CALCulate:FUNCtion?

Query the present math function. Returns PERC, AVER, NULL, LIM, MXB, DB or DBM.

CALCulate:STATe {OFF|ON}

Disable or enable the selected math function.

CALCulate:STATe?

Query the state of the math function. Returns “0”(OFF) or “1”(ON).

CALCulate:PERCent:TARGet {

<value>

|MINimum|MAXimum}

Set the target value for percent math function. The multimeter clears the value when Min/Max is
turned on, when the power has been off or a remote interface reset.

CALCulate:PERCent:TARGet? [MINimum|MAXimum]

Query the target value for percent math function.

CALCulate:AVERage:MINimum?

Read the minimum value found during the Min/Max operation. The multimeter clears the value
when Min/Max is turned on, when the power has been off or a remote interface reset.

CALCulate:AVERage:MAXimum?

Read the maximum value found during the Min/Max operation. The multimeter clears the value
when Min/Max is turned on, when the power has been off or a remote interface reset.

CALCulate:AVERage:AVERage?

Read the average value of all readings taken since the Min/Max operation has been enabled. The
multimeter clears the value when Min/Max is turned on, when the power has been off or a remote
interface reset.

«
...
123
124
125
126
127
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов