TEXIO DL-2060 Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 152

TEXIO DL-2060 Скачать руководство пользователя страница 119

113

B.5 The Measurement Configuration Command

※

This mark means that it is available with firmware version 1.05 or upward.

[SENSe:]

FUNCtion “<

function

>”

Select a measurement function and enclose it in quotes in the command string (FUNC “VOLT:DC”).
Use one of the following strings.

VOLTage:DC                                 VOLTage:AC                                  VOLTage:DC:RATio
CURRent:DC                                CURRent:AC
RESistance (for 2-wire ohms)                         FRESistance (for 4-wire ohms)
FREQuenc                                      PERiod                                             CONTinuity
DIODe                                            TCOuple                                          TEMPerature

[SENSe:]FUNCtion?

Query the measurement function and return a quoted string.

[SENSe:]<

function

>:RANGe {<

range

>|MINimum|MAXimum}

Select a range for the selected function. For frequency and period measurements, range applies to
the signal’s input voltage, not its frequency (use FREQuency:VOLTage or PERiod:VOLTage). MIN
selects the lowest range for the selected function. MAX selects the highest range.

[SENSe:]<

function

>:RANGe? [MINimum|MAXimum]

Query the range for the selected function. For frequency and period, use FREQuency:VOLTage or
PERiod:VOLTage. Autorange thresholds: Down range at <10% of range; Up range at >120% of range.

[SENSe:]<

function

>:RANGe:AUTO {OFF|ON}

Disable or enable autorange for the selected function.

[SENSe:]<

function

>:RANGe:AUTO?

Query the autorange setting. Return “1” (ON) or “0” (OFF).

[SENSe:]<

function

>:RESolution {<

resolution

>|MINimum|MAXimum}

Set resolution for the selected function (not valid for frequency, period, or ratio). Specify the
resolution in the same units as the measurement function, not in number of digits. MIN selects
the smallest value accepted, which gives the most resolution. MAX selects the largest value
accepted which gives the least resolution.

[SENSe:]<

function

>:RESolution? [MINimum|MAXimum]

Query the resolution for the selected function.

[SENSe:]UNIT {Cel|Far|K}

Select units for temperature measurement. Cel means Celsius, Far means Fahrenheit,and K
means Kelvin.

«
...
117
118
119
120
121
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов