TEXIO DL-2060 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 152

background image

111

B.4 The CONFigure Command

CONFigure:VOLTage:DC {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and configure the multimeter for DC voltage measurements with the specified range and
resolution. This command does not initiate the measurement.

CONFigure:VOLTage:DC:RATio {<range>|MIN|MAX|DEF },{<resolution>|MIN|MAX|DEF}

Preset and configure the multimeter for DC:DC ratio measurements with the specified range and
resolution. This command does not initiate the measurement. The specified range applies to the
source signal and autorange is selected for the reference signal.

CONFigure:VOLTage:AC {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and configure the multimeter for AC voltage measurements with the specified range and
resolution. This command does not initiate the measurement. For AC measurement, resolution is
fixed at 6½ digits. Therefore the resolution parameter only affects the front panel display.

CONFigure:CURRent:DC {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and configure the multimeter for DC current measurements with the specified range and
resolution. This command does not initiate the measurement.

CONFigure:CURRent:AC {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and configure the multimeter for AC current measurements with the specified range and
resolution. This command does not initiate the measurement. For AC measurement, resolution is
fixed at 6½ digits. Therefore the resolution parameter only affects the front panel display.

CONFigure:RESistance {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and configure the multimeter for 2-wire Ω measurements with the specified range and
resolution. This command does not initiate the measurement.

CONFigure:FRESistance {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and configure the multimeter for 4-wire Ω measurements with the specified range and
resolution. This command does not initiate the measurement.

CONFigure:FREQuency {<range>|MIN|MAX|DEF},{<resolution>|MIN|MAX|DEF}

Preset and configure the multimeter for frequency measurements with the specified range and
resolution. This command does not initiate the measurement. For frequency measurements, the
meter uses only one “range” for all inputs between 3Hz and 300kHz. With no input signal applied,
frequency measurements return “0”.

«
...
115
116
117
118
119
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DL-2060

Бренд: Patton electronics Страницы: 58

Бренд: Lumel Страницы: 10

Бренд: ConLAB Страницы: 10

Бренд: Armada Страницы: 3

Бренд: Tenma Страницы: 2

Бренд: Tenma Страницы: 3

Бренд: Zico Страницы: 17

Бренд: Sanwa Страницы: 26

Бренд: Extech Instruments Страницы: 6

Бренд: Clinton Electronics Страницы: 4

Escola 2 1006811

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 5

Бренд: Brymen Страницы: 16

Бренд: Delton Страницы: 2

Бренд: Delton Страницы: 2

Бренд: MAC TOOLS Страницы: 54

Бренд: Pro's Kit Страницы: 16

Бренд: Velleman components Страницы: 45

Бренд: Chauvin Arnoux Страницы: 138

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды