TEXIO DL-2060 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 152

TEXIO DL-2060 Скачать руководство пользователя страница 10

4

1.1.3 To connect the power

Check the power-line voltage on the rear panel to see if voltage setting is correct for your
area. Change the setting if it is not correct or the fuse is broken. Please follow the steps
below.

1.1.3.1 To convert the voltage

Warning! In some areas, the power supplied voltage is 240Vac or 120Vac; in others,

the power supplied voltage is 220 Vac or 100 Vac. Please refer to your local power
supplied voltage to see if you have the right setting.

Warning! Before changing the setting, make sure the multimeter is disconnected

from the AC power. An incorrect voltage setting may cause severe damage to your
instrument.

Warning! The power cord supplied with DL-2060 contains a separate ground wire

for use with grounded outlets. When proper connections are made, instrument chassis is
connected to power line ground through the ground wire in the power cord. Failure to use
a grounded outlet may result in personal injury or death due to electric shock.

This product enables to switch between the power-supply voltage of 100Vac and 220Vac
and setup either of it.

※

If you desire switching type of 120Vac and 240Vac, please contact us.

Suppose your condition is in AC 100V and you want to convert the voltage to the 220V.
Follow these steps to change the voltage setting.

【

Step 1

】

Verify that the meter is disconnected as shown in

Figure 2-1

.

Figure 2-1

«
...
8
9
10
11
12
...
»

Содержание DL-2060

























































































































































Отзывы:

Нет отзывов