Commissioning and Troubleshooting
Premier Elite Series Installation Manual
50
INS176-15
Reset and Service Messages
When the system requires attention because of a potential problem,
the display will show one of three service messages. These
messages can also be accessed at any time, allowing the user to
view installer information.
These messages would normally be programmed with the
telephone numbers of the installer or the Alarm Receiving
Centre (see page 76 for details).
To display the service messages, proceed as follows:
The display will normally show the time and date:
e a
Press
N
followed by
1
for the
Service
message:
all la o
o eice
Press
N
followed by
2
for the
Reset
message:
all Enginee o
ese yse
Press
N
followed by
3
for the
Anti-code
message:
all
ese yse
Press
R
to exit from the message, the display will then return to
normal.
When alarm information is being displayed, pressing the SCROLL
key will slow down the display and also allow manual scrolling
through the events.
Fault Warning Tones
When a fault condition occurs i.e. mains fail, line fault etc. the internal
sounders will chime every 30 seconds for 3 minutes. The chiming will
automatically stop when a valid User code is entered, when
R
is
pressed or after 3 minutes (whichever occurs first). The fault
indication will only be cleared from the display when the fault has
been rectified i.e. power, telephone line has been restored.
Fault Messages
There are system faults waiting to be
viewed, enter a valid user code to view
the faults. After entering a code faults will
be displayed for 30 seconds. If the fault is
not reset within 30 seconds, this
message will be displayed again.
The number of devices connected to the
networks has changed from the last time
a ‘Confirm Devices’ was don
e.
Engineer access is programmed for
Engineer code + User code (see page
71 for details).
The Engineers code was entered when the
system was fully armed (access to the
programming menu can only be gained
when the system is not fully armed.
The alarm engineer has logged into the
programming menu and is working on
site (this message will clear when the
engineer logs off or the system is armed).
ains oe
e a
There has been an AC Mains failure.
ah al
e a
There is a fault with the ATS (Alarm
Transmission System).
o ah ailale
e a
There are no ATS (Alarm Transmission
System) paths available.
o aey
e a
The Standby Battery has not been
connected,
aey al
e a
There is a fault with the control panel
standby battery or it is not connected.
ea ailed es
e a
Zones that have been placed on test
have failed the test.
anel id ape
e a
There is a fault with the control panel lid
tamper.
ell ape
e a
There is a fault with the bell tamper on
the control panel.
iliay ape
e a
There is a fault with the auxiliary tamper
on the control panel.
ell se lon
e a
The bell fuse on the control panel has
blown.
se lon
e a
The Auxiliary fuse on the control panel
has blown.
K ape
e a
There is a fault with the lid tamper of
Keypad X,X.
K os
e a
Keypad X,X has been lost off of the
system.
E ape
e a
There is a fault with the lid tamper of
Expander X,X
E os
e a
Expander X,X has been lost off of the
system.
E o ols
e a
The voltage at expander X,X is very low.
E ell ap
e a
The expander’s Auxiliary input (that is
programmed as bell tamper) is in fault.
E ap
e a
The expander’s Auxiliary input (that is
programmed as aux tamper) is in fault.
eice eied
e a
The service timer has expired indicating
that the system requires a service (the
system can normally still be used).
oy ode no
alloed se
The user code is locked out (normally
during entry). The system must be
disarmed using a Prox TAG.
eoe Keypad is
no KE o
To many invalid code attempts have
caused the keypad to lock out. The
keypad will remain like this for 5 minutes.
ea eced
e a
The keypad has been disabled to prevent
unauthorised access. The display will
automatically clear when it is re-enabled.
ie ing
Areas are being armed using one of the
control timers (enter a valid User code to
defer the arming for 30 minutes).
E E
e a
oni eices
e a
o need a se
o enale access
o need a se
o na syse
la Enginee
oing n ie
