manualshive.com logo in svg

Texas Instruments TMS470R1x, Справочное руководство

Поделиться
Скачать
Texas Instruments TMS470R1x Скачать руководство пользователя страница 89

Control Registers and RAM

Multi-Buffer Serial Peripheral Interface (MibSPI) (SPNU217B)

81

7.24

Transfer Group Interrupt Vector Register 0 (TGINTVECT0)

The register TGINTVECT0 returns a vector of the highest prior interrupt that
is enabled for interrupt line INT0, no matter whether it is a “transfer finished”
interrupt or a “transfer suspended” interrupt. The transfer group with the
lowest number (transfer group 0) has the highest priority.

Bits 31:6

Reserved  

Bits 5:1

INTVECT0.  

Interrupt vector for interrupt line INT0.

INTVECT0 returns the vector of the pending interrupt at interrupt line INT0. If
more than one interrupt is pending, INTVECT0 always references the highest
prior interrupt source first. The transfer group with the smallest number has
the highest priority. Reading INTVECT0 automatically updates the
TGINTVECT0 register with the interrupt vector coming next in the interrupt
priority chain and the corresponding type (SUSPEND flag). Error interrupts
have lowest priority.

Bits     

31

16

068h

Reserved

U

Bits     

15

6

5

1

0

Reserved

INTVECT0

SUSPEND

U

R-0

R-0

Legend: R = Read, W = Write, C = Clear, U = Undefined, 

-n

 = Value after reset, x = indeterminate

Содержание TMS470R1x














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды