manualshive.com logo in svg

Texas Instruments TMS320x2823x, Справочное руководство

Поделиться
Скачать
Texas Instruments TMS320x2823x Скачать руководство пользователя страница 102

Registers

www.ti.com

Table 34. Dead-Band Generator Control Register (DBCTL) Field Descriptions

Bits

Name

Value

Description

15-6

Reserved

Reserved

5-4

IN_MODE

Dead Band Input Mode Control

Bit 5 controls the S5 switch and bit 4 controls the S4 switch shown in

Figure 31

.

This allows you to select the input source to the falling-edge and rising-edge delay.

To produce classical dead-band waveforms the default is EPWMxA In is the source for both
falling and rising-edge delays.

00

EPWMxA In (from the action-qualifier) is the source for both falling-edge and rising-edge
delay.

01

EPWMxB In (from the action-qualifier) is the source for rising-edge delayed signal.

EPWMxA In (from the action-qualifier) is the source for falling-edge delayed signal.

10

EPWMxA In (from the action-qualifier) is the source for rising-edge delayed signal.

EPWMxB In (from the action-qualifier) is the source for falling-edge delayed signal.

11

EPWMxB In (from the action-qualifier) is the source for both rising-edge delay and
falling-edge delayed signal.

3-2

POLSEL

Polarity Select Control

Bit 3 controls the S3 switch and bit 2 controls the S2 switch shown in

Figure 31

.

This allows you to selectively invert one of the delayed signals before it is sent out of the
dead-band submodule.

The following descriptions correspond to classical upper/lower switch control as found in one
leg of a digital motor control inverter.

These assume that DBCTL[OUT_MODE] = 1,1 and DBCTL[IN_MODE] = 0,0. Other
enhanced modes are also possible, but not regarded as typical usage modes.

00

Active high (AH) mode. Neither EPWMxA nor EPWMxB is inverted (default).

01

Active low complementary (ALC) mode. EPWMxA is inverted.

10

Active high complementary (AHC). EPWMxB is inverted.

11

Active low (AL) mode. Both EPWMxA and EPWMxB are inverted.

1-0

OUT_MODE

Dead-band Output Mode Control

Bit 1 controls the S1 switch and bit 0 controls the S0 switch shown in

Figure 31

.

This allows you to selectively enable or bypass the dead-band generation for the falling-edge
and rising-edge delay.

00

Dead-band generation is bypassed for both output signals. In this mode, both the EPWMxA
and EPWMxB output signals from the action-qualifier are passed directly to the PWM-chopper
submodule.

In this mode, the POLSEL and IN_MODE bits have no effect.

01

Disable rising-edge delay. The EPWMxA signal from the action-qualifier is passed straight
through to the EPWMxA input of the PWM-chopper submodule.

The falling-edge delayed signal is seen on output EPWMxB. The input signal for the delay is
determined by DBCTL[IN_MODE].

10

The rising-edge delayed signal is seen on output EPWMxA. The input signal for the delay is
determined by DBCTL[IN_MODE].

Disable falling-edge delay. The EPWMxB signal from the action-qualifier is passed straight
through to the EPWMxB input of the PWM-chopper submodule.

11

Dead-band is fully enabled for both rising-edge delay on output EPWMxA and falling-edge
delay on output EPWMxB. The input signal for the delay is determined by DBCTL[IN_MODE].

102

TMS320x2833x, 2823x Enhanced Pulse Width Modulator (ePWM) Module

SPRUG04A – October 2008 – Revised July 2009

Submit Documentation Feedback

© 2008–2009, Texas Instruments Incorporated

Содержание TMS320x2823x




















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды