manualshive.com logo in svg

Texas Instruments TMS320VC5509, Справочное руководство


Поделиться
Скачать
background image

Setting the SRG Input Clock Polarity

8-39

Transmitter Configuration

SPRU592E

Table 8

−

27. Register Bits Used to Set the SRG Input Clock Polarity (Continued)

Register

Function

Name

Bit

PCR

0

CLKRP

CLKR Pin Polarity
CLKRP determines the input clock polarity when the CLKR pin supplies the
input clock (SCLKME = 1 and CLKSM = 0).

CLKRP = 0

Rising edge on CLKR pin generates transitions on CLKG
and FSG.

CLKRP = 1

Falling edge on CLKR pin generates transitions on CLKG
and FSG.

8.24.1 Using CLKSP/CLKXP/CLKRP to Choose an Input Clock Polarity

The sample rate generator can produce a clock signal (CLKG) and a
frame-sync signal (FSG) for use by the receiver, the transmitter, or both. To
produce CLKG and FSG, the sample rate generator must be driven by an input
clock signal derived from the McBSP internal input clock or from an external
clock on the CLKX pin, CLKR pin, or (if present) CLKS pin. If you use a pin,
choose a polarity for the SRG input clock by programming the appropriate
polarity bit (CLKXP for the CLKX pin, CLKRP for the CLKR pin, CLKSP for the
CLKS pin). The polarity determines whether the rising or falling edge of the
input clock generates transitions on CLKG and FSG.

Note:

On TMS320VC5501 and TMS320VC5502 devices, the polarity of the

SRG input clock is always positive (rising edge), regardless of CLKRP or

CLKXP.

Содержание TMS320VC5509






























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320VC5509

Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Бренд: Panasonic Страницы: 4
Abus TVVR36500 User Manual preview
TVVR36500
Бренд: Abus Страницы: 60
Alcad ZA-431 Quick Start Manual preview
ZA-431
Бренд: Alcad Страницы: 6
Xilica Audio Design XP 4080 User Manual preview
XP 4080
Бренд: Xilica Audio Design Страницы: 30
JUMO iTRON B 70.2040 Operating Instructions Manual preview
iTRON B 70.2040
Бренд: JUMO Страницы: 41
IBASE Technology FWA8207 Series User Manual preview
FWA8207 Series
Бренд: IBASE Technology Страницы: 39
Ubiquiti PowerBeam PBE-5AC-400-ISO Quick Start Manual preview
PowerBeam PBE-5AC-400-ISO
Бренд: Ubiquiti Страницы: 23
B&B Electronics 232PCC User Manual preview
232PCC
Бренд: B&B Electronics Страницы: 17
nox Hummer H-240CL Manual preview
Hummer H-240CL
Бренд: nox Страницы: 16
ICP DAS USA PIO-821 Series User Manual preview
PIO-821 Series
Бренд: ICP DAS USA Страницы: 62
Patton electronics OnSite 9100 Quick Start Manual preview
OnSite 9100
Бренд: Patton electronics Страницы: 8
Intel Core 2 Duo E4300 Design Manual preview
Core 2 Duo E4300
Бренд: Intel Страницы: 55
ST ST7-EMU3 Series User Manual preview
ST7-EMU3 Series
Бренд: ST Страницы: 39
Intel 80C186EC Manual preview
80C186EC
Бренд: Intel Страницы: 57
IEI Technology PUZZLE-5030 User Manual preview
PUZZLE-5030
Бренд: IEI Technology Страницы: 119
Renesas RL78 Series User Manual preview
RL78 Series
Бренд: Renesas Страницы: 31
Terasic DE10-Agiles User Manual preview
DE10-Agiles
Бренд: Terasic Страницы: 208
3Ware 9500S-8 - Escalade RAID Controller User Manual preview
9500S-8 - Escalade RAID Controller
Бренд: 3Ware Страницы: 46

Бренды по названию

Популярные бренды

Загрузить еще бренды