Texas Instruments TMS320F2837 D Series страница 16 Скачать руководство пользователя | Manualshive

Страница: 16 / 48

background image

Usage Notes and Known Design Exceptions to Functional Specifications

16

SPRZ412K – December 2013 – Revised February 2020

Submit Documentation Feedback

Copyright © 2013–2020, Texas Instruments Incorporated

TMS320F2837xD Dual-Core MCUs Silicon Revisions C, B, A, 0

Advisory

XRS may Toggle During Power Up

Revision(s) Affected

0, A, B

Details

During device power up, the XRS pin may toggle high prematurely. After the V

DDIO

and

V

DD

supplies reach the recommended operation conditions, the XRS pin behavior will be

per the pin description. This is only an issue with the external state of the XRS pin.
Internally, the device will be held in reset by the POR logic until the supplies are within
an acceptable range and XRS is high.

Workaround(s)

Disregard XRS activity on the board prior to supplies reaching recommended operating
conditions.

Advisory

USB: USB DMA Event Triggers are not Supported

Revision(s) Affected

0, A, B, C

Details

The USB module generates inadvertent extra DMA requests, causing the FIFO to
overflow (on IN endpoints) or underflow (on OUT endpoints). This causes invalid IN
DATA packets (larger than the maximum packet size) and duplicate receive data.

Workaround(s)

None

Advisory

VREG: VREG Will be Enabled During Power Up Irrespective of VREGENZ

Revision(s) Affected

0, A, B

Details

During power up of the 3.3-V V

DDIO

, the internal Voltage Regulator (VREG) will be active

until the 1.2-V V

DD

supply reaches approximately 0.7 V. After this time, the VREGENZ

pin tied to V

DDIO

will disable the internal VREG. This will not impact device operation.

Workaround(s)

None

«
...
14
15
16
17
18
...
»

Содержание TMS320F2837 D Series

















































Отзывы:

Нет отзывов

Похожие инструкции для TMS320F2837 D Series

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: Galcon Страницы: 32

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: Datapath Страницы: 12

Бренд: Samson Страницы: 2

FUTERA XLF Series

Бренд: RBI Страницы: 128

Бренд: RBH Access Technologies Страницы: 36

Бренд: S&C Страницы: 11

Бренд: S&C Страницы: 24

Бренд: S&C Страницы: 19

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 128

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 80

Бренд: Haehne Страницы: 44

SMARC conga-SMX8-X

Бренд: Congatec Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды