Texas Instruments TMS320C6670 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 226

background image

108

Device Operating Conditions

Copyright 2012 Texas Instruments Incorporated

SPRS689D—March 2012

Multicore Fixed and Floating-Point System-on-Chip

TMS320C6670

Submit Documentation Feedback

6.4 Power Supply to Peripheral I/O Mapping

Table 6-4

Power Supply to Peripheral I/O Mapping

(1) (2)

Over Recommended Ranges of Supply Voltage and Operating Case Temperature (Unless Otherwise Noted)

1 Please note that this table does not attempt to describe all functions of all power supply terminals but only those whose purpose it is to power peripheral I/O buffers and

clock input buffers.

2 Please see the

Hardware Design Guide for KeyStone Devices

in

2.9 ‘‘Related Documentation from Texas Instruments’’ on page 66

for more information about individual

peripheral I/O.

Power Supply

I/O Buffer Type

Associated Peripheral

CVDD

Supply core voltage

LJCB

SYSCLK(P|N) PLL input buffer

ALTCORECLK(P|N) PLL input buffer

SRIOSGMIICLK(P|N) SerDes PLL input buffer

DDRCLK(P|N) PLL input buffer

PCIECLK(P|N) SerDes PLL input buffer

MCMCLK(P|N) SerDes PLL input buffer

PASSCLK(P|N) PLL input buffer

DVDD15

1.5-V supply I/O voltage

DDR3 (1.5 V)

All DDR3 memory controller peripheral I/O buffer

DVDD18

1.8-V supply I/O voltage

LVCMOS (1.8V)

All GPIO peripheral I/O buffer

All JTAG and EMU peripheral I/O buffer

All TIMER0-8 peripheral I/O buffer

All SPI peripheral I/O buffer

All AIF peripheral I/O buffer

All RESETs, NMI, control peripheral I/O buffer

All SmartReflex peripheral I/O buffer

All Hyperlink sideband peripheral I/O buffer

All MDIO peripheral I/O buffer

All UART peripheral I/O buffer

Open-drain (1.8 V)

All I

2

C peripheral I/O buffer

VDDT1

Hyperlink SerDes termination and analogue front-end supply

SerDes/CML

Hyperlink SerDes CML IO buffer

VDDT2

SRIO/SGMII/PCIE SerDes termination and analog front-end
supply

SerDes/CML

SRIO/SGMII/PCIE SerDes CML IO buffer

VDDT3

AIF termination and analog front-end supply

SerDes/CML

AIF SerDes CML IO buffer

End of Table 6-4

«
...
106
107
108
109
110
...
»

Содержание TMS320C6670



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6670

Бренд: Danfoss Страницы: 32

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 44

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 144

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 8

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 6

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 2

ECL Comfort 110

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 24

Бренд: ECKELMANN Страницы: 178

Бренд: VAT Страницы: 27

Бренд: ICP DAS USA Страницы: 148

Бренд: ICMA Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды