manualshive.com logo in svg

Texas Instruments TMS320C6201, Справочное руководство


Поделиться
Скачать
background image

JTAG Emulator Cable Pod Signal Timing

15-5

Designing for JTAG Emulation

15.5 JTAG Emulator Cable Pod Signal Timing

Figure 15–3 shows the signal timings for the emulator cable pod. Table 15–2
defines the timing parameters. These timing parameters are calculated from
values specified in the standard data sheets for the emulator and cable pod
and are for reference only. Texas Instruments does not test or guarantee these
timings.

The emulator pod uses TCK_RET as its clock source for internal synchroni-
zation. TCK is provided as an optional target system test clock source.

Figure 15–3. JTAG Emulator Cable Pod Timings

TDO

TMS/TDI

TCK_RET

6

5

4

3

2

1

1.5 V

Table 15–2. Emulator Cable Pod Timing Parameters

No.

 Reference

  Description

Min

Max

Units

1

t

c(TCK)

TCK_RET period

35

200

ns

2

t

w(TCKH)

TCK_RET high-pulse duration

15

ns

3

t

w(TCKL)

TCK_RET low-pulse duration

15

ns

4

t

d(TMS)

Delay time, TMS/TDI valid from TCK_RET low

6

20

ns

5

t

su(TDO)

TDO setup time to TCK_RET high

3

ns

6

t

h(TDO)

TDO hold time from TCK_RET high

12

ns

Содержание TMS320C6201






























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6201

Magnat Audio MC 200 Faq preview
MC 200
Бренд: Magnat Audio Страницы: 2
dbx Zone Pro 640 Manual preview
Zone Pro 640
Бренд: dbx Страницы: 2
dbx 166 Quick Start Manual preview
166
Бренд: dbx Страницы: 17
Idis DR-8416 Operation Manual preview
DR-8416
Бренд: Idis Страницы: 123
Idis DR-6232H Installation Manual preview
DR-6232H
Бренд: Idis Страницы: 29
Idis DR-4516P Installation Manual preview
DR-4516P
Бренд: Idis Страницы: 28
Idis DirectIP DR-1304P Operation Manual preview
DirectIP DR-1304P
Бренд: Idis Страницы: 82
IAR SYSTEMS IAR KickStart Kit TWR-K60N512-IAR Getting Started Manual preview
IAR KickStart Kit TWR-K60N512-IAR
Бренд: IAR SYSTEMS Страницы: 8
Gate NanoAAB User Manual preview
NanoAAB
Бренд: Gate Страницы: 8
Cromemco 32K Bytesaver Instruction Manual preview
32K Bytesaver
Бренд: Cromemco Страницы: 46
Verizon Wireless PC 3220 Owner'S Manual preview
PC 3220
Бренд: Verizon Wireless Страницы: 39
TANDBERG D5018501 Hardware User Manual preview
D5018501
Бренд: TANDBERG Страницы: 3
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Бренд: Ubiquiti Страницы: 13
Uctronics U6187 Assembly Manual preview
U6187
Бренд: Uctronics Страницы: 12
Lindy Modular Fast Fiber Switch Converter MT-RJ Specifications preview
Modular Fast Fiber Switch Converter MT-RJ
Бренд: Lindy Страницы: 3
LevelOne ServCon FPS-3003 Quick Install Manual preview
ServCon FPS-3003
Бренд: LevelOne Страницы: 45
FDI UEZGUI-4357-70WVN User Manual preview
UEZGUI-4357-70WVN
Бренд: FDI Страницы: 30
Motorola M68MM01 Manual preview
M68MM01
Бренд: Motorola Страницы: 41

Бренды по названию

Популярные бренды

Загрузить еще бренды