manualshive.com logo in svg

Texas Instruments TMS320C6201, Справочное руководство


Поделиться
Скачать
background image

Expansion Bus Host Port Operation

 

8-26

8.5.2

Synchronous Host Port Mode

In this mode host port has address and data signals multiplexed and is i960Jx
compatible. This allows a minimum glue interface to the PCI bus, since major
PCI interface chip manufacturers adopted the i960 bus for local bus on their
chips.

The synchronous host port can also easily interface to many other common
processors, and essentially act in a slave only mode. This is done by simply
not initiating transactions on the expansion bus.

The ‘C6202 expansion bus has the capability to initiate and receive burst trans-
fers.

Table 8–16 lists pin function in the expansion bus synchronous host port
mode:

Table 8–16. Expansion Bus Pin Description (Synchronous Host Port Mode) 

Signal
Symbol

Signal

Type

Signal

Count

Signal
Name

Signal Function

XCLKIN

I

1

Clock
Input

Expansion bus clock (maximum clock speed is 1/4 of the
CPU clock speed.

XCS

I

1

Chip
Select

Selects the ‘C6202 as a target of an external master.

XHOLD

I/O/Z

1

Hold
Request

Case 1 (Internal bus arbiter enabled)

XHOLD is asserted by external device to request use of the
expansion bus. The ‘C6202 asserts XHOLDA when control
is granted.

Case 2 (Internal bus arbiter disabled)

The ‘C6202 wakes up from reset as slave on the bus.

XHOLD is asserted by ‘C6202 to request use of the
expansion bus. The expansion bus arbiter asserts
XHOLDA when control is granted.

XHOLDA

I/O/Z

1

Hold 
acknowledge

Case 1 (Internal bus arbiter disabled)

The ‘C6202 wakes up from reset as slave on the bus.

The expansion bus arbiter asserts XHOLDA when control
is granted in response to XHOLD. The bus should not be
granted to ‘C6202 unless requested by XHOLD.

Case 2 (Internal bus arbiter enabled)

The ‘C6202 wakes up from reset as master of the bus.

XHOLDA is asserted by the ‘C6202 when control is granted
in response to XHOLD.

Содержание TMS320C6201






























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6201

Datasat AP20 Installation And Operating Manual preview
AP20
Бренд: Datasat Страницы: 32
Data Translation DT330 Series Getting Started Manual preview
DT330 Series
Бренд: Data Translation Страницы: 60
Paradyne 3172 Quick Reference preview
3172
Бренд: Paradyne Страницы: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Бренд: Paradyne Страницы: 2
Ensemble Designs Avenue Express Control Panel Data Pack preview
Avenue Express Control Panel
Бренд: Ensemble Designs Страницы: 19
ADC PG-FlexPlus AMU-912 Manual preview
PG-FlexPlus AMU-912
Бренд: ADC Страницы: 130
Fieldbus Specialists AT-FBUS Getting Started preview
AT-FBUS
Бренд: Fieldbus Specialists Страницы: 39
addlink SPIDER N4 Installation Manual preview
SPIDER N4
Бренд: addlink Страницы: 9
SIIG 1394 Dual-Port CardBus Quick Installation Manual preview
1394 Dual-Port CardBus
Бренд: SIIG Страницы: 8
Arbor Technology Em104P-i2904 Quick Installation Manual preview
Em104P-i2904
Бренд: Arbor Technology Страницы: 8
BIIZZY zoomno MSC-5578 Setup Instructions preview
zoomno MSC-5578
Бренд: BIIZZY Страницы: 2
ZALMAN ZM80C-HP Manual preview
ZM80C-HP
Бренд: ZALMAN Страницы: 18
Corsair H80i v2 Quick Start Manual preview
H80i v2
Бренд: Corsair Страницы: 12
Buffalo AirStation G54 WLA2-G54 Quick Setup Manual preview
AirStation G54 WLA2-G54
Бренд: Buffalo Страницы: 8
c SwiftreaderX Installation Manual preview
SwiftreaderX
Бренд: c Страницы: 32
Intel RS2BL040 - Raid Controller Configuration Manual preview
RS2BL040 - Raid Controller
Бренд: Intel Страницы: 5
IEI Technology IMBA-C604EP User Manual preview
IMBA-C604EP
Бренд: IEI Technology Страницы: 213
Iomega ZIP drive 100 User Manual preview
ZIP drive 100
Бренд: Iomega Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды