manualshive.com logo in svg

Texas Instruments TMS320C6201, Справочное руководство


Поделиться
Скачать
background image

Overview

 

7-2

7.1

Overview

The host-port interface (HPI) is a 16-bit-wide parallel port through which a host
processor can directly access the CPU’s memory space. The host device func-
tions as a master to the interface, which increases ease of access. The host
and CPU can exchange information via internal or external memory. The host
also has direct access to memory-mapped peripherals. Connectivity to the
CPU’s memory space is provided through the DMA controller. Dedicated
address and data registers not accessible to the CPU connect the HPI to the
DMA auxiliary channel, which connects the HPI to the CPU’s memory space.
Both the host and the CPU can access the HPI control register (HPIC). The
host can access the HPI address register (HPIA), the HPI data register (HPID),
and the HPIC by using the external data and interface control signals.

Figure 7–1 shows the host-port components in the block diagram of the on-
chip peripherals.

Figure 7–1. TMS320C6201/C6701 Block Diagram

Program memory/cache

Program memory controller

EMIF

PLL

Host port interface

DMA

controller

bus

Peripheral

EMIF control

DMA control

HPI control

McBSPs

Interrupt selector

Timers

Data memory

controller

Data memory

CPU core

2

Data path

1

Data path

Instruction decode

Instruction dispatch

Program fetch

down

Power

Boot

configuration

controller

Содержание TMS320C6201






























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6201

ebm-papst VBH0630CTTRS Operating Instructions Manual preview
VBH0630CTTRS
Бренд: ebm-papst Страницы: 16
Zonet ZUN2200 Quick Installation Manual preview
ZUN2200
Бренд: Zonet Страницы: 2
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Бренд: ICP DAS USA Страницы: 8
red lion Yaskawa 2000 Information Sheet preview
Yaskawa 2000
Бренд: red lion Страницы: 5
WABCO CAN Router Manual preview
CAN Router
Бренд: WABCO Страницы: 29
AXIOMTEK CEM820 Series User Manual preview
CEM820 Series
Бренд: AXIOMTEK Страницы: 58
Laser UDC CARD User Manual preview
UDC CARD
Бренд: Laser Страницы: 4
Sony Ericsson GC79 User Manual preview
GC79
Бренд: Sony Ericsson Страницы: 93
Xinje VH5 Series User Manual preview
VH5 Series
Бренд: Xinje Страницы: 76
Juniper WX 100 Quick Start Manual preview
WX 100
Бренд: Juniper Страницы: 6
NEC N8154-25 User Manual preview
N8154-25
Бренд: NEC Страницы: 47
Renesas H8S/2615 Series User Manual preview
H8S/2615 Series
Бренд: Renesas Страницы: 28
THOMSON SPEEDTOUCH 110G Setup And User Manual preview
SPEEDTOUCH 110G
Бренд: THOMSON Страницы: 26
Safety Vision ROADRECORDER 8400 NVR User Manual preview
ROADRECORDER 8400 NVR
Бренд: Safety Vision Страницы: 27
Disc Makers ElitePro User Manual preview
ElitePro
Бренд: Disc Makers Страницы: 12
PairGain T1L2F10A Manual preview
T1L2F10A
Бренд: PairGain Страницы: 76
Cognex 800-5815-1 Installation And Reference Manual preview
800-5815-1
Бренд: Cognex Страницы: 57
Silex technology Embedded Intelligent Module SX-560 Developer'S Reference Manual preview
Embedded Intelligent Module SX-560
Бренд: Silex technology Страницы: 110

Бренды по названию

Популярные бренды

Загрузить еще бренды