manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

14.6.2.11 I2C Interrupt Source (I2CISRC) Register (Offset = Ah) [reset = 0h]

The I2C interrupt source register (I2CISRC) is a 16-bit register used by the CPU to determine which event 
generated the I2C interrupt.

Figure 14-29. I2C Interrupt Source (I2CISRC) Register

15

14

13

12

11

10

9

8

RESERVED

WRITE_ZEROS

R-0h

R/W-0h

7

6

5

4

3

2

1

0

RESERVED

INTCODE

R-0h

R-0h

Table 14-20. I2C Interrupt Source (I2CISRC) Register Field Descriptions

Bit

Field

Type

Reset

Description

15-12

RESERVED

R

0h

Reserved

11-8

WRITE_ZEROS

R/W

0h

TI internal testing bits
These reserved bit locations should always be written as zeros.
Reset type: SYSRSn

7-3

RESERVED

R

0h

Reserved

2-0

INTCODE

R

0h

Interrupt code bits.
The binary code in INTCODE indicates the event that generated an 
I2C interrupt.
A CPU read will clear this field. If another lower priority interrupt is 
pending and enabled, the value corresponding to that interrupt will 
then be loaded. Otherwise, the value will stay cleared.
In the case of an arbitration lost, a no-acknowledgment condition 
detected, or a stop condition detected, a CPU read will also clear 
the associated interrupt flag bit in the I2CSTR register. Inversely, in 
the case of a Register-access-ready (ARDY), a Receive-data-ready 
(RRDY), a Transmit-data-ready (XRDY), or an Adressed-as-slave 
(AAS) condition, a CPU read will NOT clear the associated interrupt 
flag bit in the I2CSTR register
Debug probe reads will not affect the state of this field or of the 
status bits in the I2CSTR register.
Reset type: SYSRSn
0h (R/W) = None
1h (R/W) = Arbitration lost
2h (R/W) = No-acknowledgment condition detected
3h (R/W) = Registers ready to be accessed
4h (R/W) = Receive data ready
5h (R/W) = Transmit data ready
6h (R/W) = Stop condition detected
7h (R/W) = Addressed as slave

www.ti.com

Inter-Integrated Circuit Module (I2C)

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

871

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Gardena 4040 Operating Instructions Manual preview
4040
Бренд: Gardena Страницы: 100
Hach SC1500 User Manual preview
SC1500
Бренд: Hach Страницы: 86
Elby Designs ASM301-ADSR Diagrams preview
ASM301-ADSR
Бренд: Elby Designs Страницы: 4
V2 FORTECO 2500-I Manual preview
FORTECO 2500-I
Бренд: V2 Страницы: 108
Holars AS H-TAG User Manual preview
H-TAG
Бренд: Holars AS Страницы: 15
SAMES KREMLIN LP 6 - 0.5/4 Translation From The Original Manual preview
LP 6 - 0.5/4
Бренд: SAMES KREMLIN Страницы: 5
NEC V850E/RS1 User Manual preview
V850E/RS1
Бренд: NEC Страницы: 852
Dasko Electronic DSS2 T-BIS_P Manual preview
DSS2 T-BIS_P
Бренд: Dasko Electronic Страницы: 4
Taco Electronic Solutions iWorx ZXU1 Installation Manual preview
iWorx ZXU1
Бренд: Taco Electronic Solutions Страницы: 24
Galil Motion Control DMC-14 5 Series Manual preview
DMC-14 5 Series
Бренд: Galil Motion Control Страницы: 200
AGS Merlin 1000SW+ Installation Operation & Maintenance preview
Merlin 1000SW+
Бренд: AGS Страницы: 12
BWT PLATINE DE SPA SP800 Installation Instructions Manual preview
PLATINE DE SPA SP800
Бренд: BWT Страницы: 48
Genius GE-R4 Manual preview
GE-R4
Бренд: Genius Страницы: 13
Welbilt Frymaster YUM WINGSTREET K3000 Operation Manual preview
Frymaster YUM WINGSTREET K3000
Бренд: Welbilt Страницы: 16
CS-Lab CSMIO/IP-A Tuning Manual preview
CSMIO/IP-A
Бренд: CS-Lab Страницы: 20
Magnetek IMPULSE G+ Series 3 Instruction Manual preview
IMPULSE G+ Series 3
Бренд: Magnetek Страницы: 9
Carrier WSHP Open v3 Integration Manual preview
WSHP Open v3
Бренд: Carrier Страницы: 58
Full Gauge Controls MT-514e Manual preview
MT-514e
Бренд: Full Gauge Controls Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды