manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Table 11-1. Peripheral Interrupt Trigger Source Options

Peripheral

Interrupt Trigger Source

CPU

DMA Software bit (CHx.CONTROL.PERINTFRC) only

ADC

ADCINT 1

ADCINT 2

External Interrupts

External Interrupt 1

External Interrupt 2

External Interrupt 3

CPU Timers

Timer 0 Overflow

Timer 1 Overflow

Timer 2 Overflow

McBSP

McBSP Transmit Buffer Empty

McBSP Receive Buffer Full

ePWM2

ADC Start of Conversion A

ADC Start of Conversion B

ePWM3

ADC Start of Conversion A

ADC Start of Conversion B

ePWM4

ADC Start of Conversion A

ADC Start of Conversion B

ePWM5

ADC Start of Conversion A

ADC Start of Conversion B

ePWM6

ADC Start of Conversion A

ADC Start of Conversion B

ePWM7

ADC Start of Conversion A

ADC Start of Conversion B

USB

USB Endpoint 1 Receive Full

USB

USB Endpoint 1 Transmit Empty

USB

USB Endpoint 2 Receive Full

USB

USB Endpoint 2 Transmit Empty

USB

USB Endpoint 3 Receive Full

USB

USB Endpoint 3 Transmit Empty

 

11.3.3 DMA Bus

The DMA bus architecture consists of a 22-bit address bus, a 32-bit data read bus, and a 32-bit data write bus. 
Memories and register locations connected to the DMA bus are via interfaces that sometimes share resources 
with the CPU memory or peripheral bus. Arbitration rules are defined in 

Section 11.5

. The following resources 

are connected to the DMA bus:
• L5 SARAM
• L6 SARAM
• L7 SARAM
• L8 SARAM
• ADC Memory Mapped Result Registers
• McBSP Data Receive Registers (DRR2/DRR1) and Data Transmit Registers (DXR2/DXR1)
• ePWM1-8/HRPWM1-8 Registers
• USB Transmit and Receive Endpoints 1-3

www.ti.com

Direct Memory Access (DMA) Module

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

731

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Tapeswitch C6 Technical Manual preview
C6
Бренд: Tapeswitch Страницы: 13
e-BLEACH infinity User Manual preview
infinity
Бренд: e-BLEACH Страницы: 24
Federal Signal Corporation ultravoice UV Installation, Operation And Service Manual preview
ultravoice UV
Бренд: Federal Signal Corporation Страницы: 79
Federal Signal Corporation PAGASYS GEN II Description, Installation, And User Manual preview
PAGASYS GEN II
Бренд: Federal Signal Corporation Страницы: 32
Lab.gruppen LAB.LEVEL4 Quick Start Manual preview
LAB.LEVEL4
Бренд: Lab.gruppen Страницы: 2
W.E.ST. SCU-138-P Technical Documentation Manual preview
SCU-138-P
Бренд: W.E.ST. Страницы: 34
Ltech TT-DX-R4-5A Manual preview
TT-DX-R4-5A
Бренд: Ltech Страницы: 4
Motor Guard M-60R Instructions preview
M-60R
Бренд: Motor Guard Страницы: 2
Renogy Rover 100A Manual preview
Rover 100A
Бренд: Renogy Страницы: 36
HANYOUNG NUX TPR-3SL-EP Instruction Manual preview
TPR-3SL-EP
Бренд: HANYOUNG NUX Страницы: 4
rotork Bifold EHPC210 Firmware Manual preview
Bifold EHPC210
Бренд: rotork Страницы: 22
3M Touch Screen Controller RX142 Reference Manual preview
Touch Screen Controller RX142
Бренд: 3M Страницы: 29
Fairford agility AGY-101 User Manual preview
agility AGY-101
Бренд: Fairford Страницы: 127
National Instruments cRIO-9037 Getting Started Manual preview
cRIO-9037
Бренд: National Instruments Страницы: 20
Arbor Technology ELIT-1270 User Manual preview
ELIT-1270
Бренд: Arbor Technology Страницы: 79
SHOWTEC 70237 Manual preview
70237
Бренд: SHOWTEC Страницы: 20
Baldor Nextmove ESB Installation Manual preview
Nextmove ESB
Бренд: Baldor Страницы: 98
Control Microsystems SCADAPack LP Hardware Manual preview
SCADAPack LP
Бренд: Control Microsystems Страницы: 47

Бренды по названию

Популярные бренды

Загрузить еще бренды