Texas Instruments TMS320*280 Series Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 94

background image

www.ti.com

4.1

Boot ROM Version and Checksum Information

4.2

Bootloader Code Revision History

Boot ROM Version and Checksum Information

The boot ROM contains its own version number located at address 0x3F FFBA. This version number
starts at 1 and will be incremented any time the boot ROM code is modified. The next address, 0x3F
FFBB contains the month and year (MM/YY in decimal) that the boot code was released. The next four
memory locations contain a checksum value for the boot ROM. Taking a 64-bit summation of all
addresses within the ROM, except for the checksum locations, generates this checksum.

Table 4-1. Bootloader Revision and Checksum

Information

Address

Contents

0x3F FFB9

Flash API silicon compatibility check.
This location is read by some versions of
the flash API to make sure it is running
on a compatible silicon version.

0x3F FFBA

Boot ROM Version Number

0x3F FFBB

MM/YY of release (in decimal)

0x3F FFBC

Least significant word of checksum

0x3F FFBD

. . .

0x3F FFBE

. . .

0x3F FFBF

Most significant word of checksum

The following table shows the boot ROM revision per device. A revision history and code listing for the
latest boot ROM code can be found in

. In addition, a .zip file with each revision of the boot

ROM code can be downloaded from the TI website at the same location as this document.

Table 4-2. Bootloader Revision Per Device

Device(s)

Silicon REVID

Boot ROM Revision

(Address 0x883)

F2808, F2806,

0 (First silicon)

Version 1

F2802, F2801

F2808, F2806,

1 (Rev A)

Version 2

F2802, F2801

F2808, F2806,

2 (Rev B) and later

Version 3

F2802, F2801

C2802, C2801

0 (First silicon) and

Version 3

later

F2809

0 (First silicon)

Version 4

F28044

0 (First silicon)

Version 4

•

Version 4, Released: April 2006
The following changes were made in V4:

–

The ITRAP vector location in the CPU vector table was changed to point to an ITRAP interrupt
service routine located within the boot ROM. This ISR attempts to enable the watchdog and then
loops until the device resets. This vector will be used for any ITRAP that occurs after reset and
before the user initializes and enables the PIE vector table. In previous revisions of the boot ROM
code, this vector pointed to a memory location in M0 SARAM.

–

The version number, release date and checksum memory locations have been updated to reflect
the new release.

•

Version 3, Released: April 2005
The following changes were made in V3:

–

The contents of the flash API silicon compatibility location (0x3F FFB9) was changed from 0xFFFF

56

Bootloader Code Overview

SPRU722C – November 2004 – Revised October 2006

Submit Documentation Feedback

«
...
54
55
56
57
58
...
»

Содержание TMS320*280 Series































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320*280 Series

Бренд: Teagle Страницы: 40

Бренд: Idis Страницы: 86

Бренд: Paradyne Страницы: 2

EK-FC1080 GTX Ti TF6

Бренд: ekwb Страницы: 2

MegaRAID SCSI 320-2X

Бренд: LSI Страницы: 4

Surround Dongle

Бренд: Sennheiser Страницы: 18

Бренд: Z Microsystems Страницы: 51

PCIe/PXIe-6301 Series

Бренд: JYTEK Страницы: 46

Бренд: Idis Страницы: 17

PFC Chokes PFC3515V Series

Бренд: Delta Electronics Страницы: 1

See3CAM 30 Z10X

Бренд: e-con Systems Страницы: 14

Бренд: ENERMAX Страницы: 33

Бренд: B&B Electronics Страницы: 24

Бренд: Beckhoff Страницы: 84

Бренд: Homeworks Страницы: 24

Бренд: LevelOne Страницы: 2

CG9103-2RS232-1USB

Бренд: BiPOM Electronics Страницы: 8

Бренд: Kontron Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды