background image

1

SLOU483 – August 2017

Submit Documentation Feedback

Copyright © 2017, Texas Instruments Incorporated

THS3491RGT Evaluation Module

User's Guide

SLOU483 – August 2017

THS3491RGT Evaluation Module

This document provides information about the evaluation module of the amplifier under test. Additionally,
this document provides a good example of printed-circuit board (PCB) design for high-speed applications.
Remember the following points:

TI recommends initially reviewing the data sheet of the device under test.

Review the schematic and layout of the THS3491RGT EVM to determine the design techniques used
in the evaluation board.

The high-speed amplifier PCB design should be approached with care and special attention must be
provided to the board parasitic which impacts the overall system performance.

Contents

1

Introduction

...................................................................................................................

2

2

EVM Default Configuration

.................................................................................................

3

3

Using the THS3491 EVM

...................................................................................................

5

4

High-Speed Amplifier PCB Layout Tips

...................................................................................

6

5

EVM Hardware Description

.................................................................................................

7

List of Figures

1

THS3491RGT EVM Default Configuration Setup Block Diagram

.....................................................

3

2

Output Interface to the Measuring Instrument

...........................................................................

4

3

Full Schematic of the THS3491RGT EVM

...............................................................................

9

4

Top Components and Silk Screen Layer

................................................................................

10

5

Layer 2 - GND

..............................................................................................................

10

6

Layer 3 - GND

..............................................................................................................

11

7

Layer 4 - GND/Signal

......................................................................................................

11

8

Layer 5 - GND

..............................................................................................................

12

9

Layer 6 - GND

..............................................................................................................

12

10

Layer 7 - GND

..............................................................................................................

13

11

Bottom Components and Silk Screen Layer

............................................................................

13

List of Tables

1

THS3491RGT EVM Bill of Materials

......................................................................................

7

Trademarks

PowerPAD is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.

Содержание THS3491RGT EVM




















Отзывы: