manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Техническое справочное руководство

Поделиться
Скачать
Texas Instruments SimpleLink Ethernet MSP432E401Y Скачать руководство пользователя страница 402

System Control Registers

www.ti.com

402

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

System Control

Table 4-166. PCGPIO Register Field Descriptions

Bit

Field

Type

Reset

Description

31-18

RESERVED

R

0x0

17

P17

R/W

0x1

GPIO Port T Power Control. The Pn bit encodings do not apply if the
corresponding bit in the RCGCGPIO, SCGCGPIO, or DCGCGPIO
register is clear.

0x0 = GPIO port T is not powered and does not receive a clock. In
this case, the state of the module is not retained. This configuration
provides the lowest power consumption state.

0x1 = GPIO port T is powered but does not receive a clock. In this
case, the module is inactive.

16

P16

R/W

0x1

GPIO Port S Power Control. The Pn bit encodings do not apply if the
corresponding bit in the RCGCGPIO, SCGCGPIO, or DCGCGPIO
register is clear.

0x0 = GPIO port S is not powered and does not receive a clock. In
this case, the state of the module is not retained. This configuration
provides the lowest power consumption state.

0x1 = GPIO port S is powered but does not receive a clock. In this
case, the module is inactive.

15

P15

R/W

0x1

GPIO Port R Power Control. The Pn bit encodings do not apply if the
corresponding bit in the RCGCGPIO, SCGCGPIO, or DCGCGPIO
register is clear.

0x0 = GPIO port R is not powered and does not receive a clock. In
this case, the state of the module is not retained. This configuration
provides the lowest power consumption state.

0x1 = GPIO port R is powered but does not receive a clock. In this
case, the module is inactive.

14

P14

R/W

0x1

GPIO Port Q Power Control. The Pn bit encodings do not apply if the
corresponding bit in the RCGCGPIO, SCGCGPIO, or DCGCGPIO
register is clear.

0x0 = GPIO port Q is not powered and does not receive a clock. In
this case, the state of the module is not retained. This configuration
provides the lowest power consumption state.

0x1 = GPIO port Q is powered but does not receive a clock. In this
case, the module is inactive.

13

P13

R/W

0x1

GPIO Port P Power Control. The Pn bit encodings do not apply if the
corresponding bit in the RCGCGPIO, SCGCGPIO, or DCGCGPIO
register is clear.

0x0 = GPIO port P is not powered and does not receive a clock. In
this case, the state of the module is not retained. This configuration
provides the lowest power consumption state.

0x1 = GPIO port P is powered but does not receive a clock. In this
case, the module is inactive.

12

P12

R/W

0x1

GPIO Port N Power Control. The Pn bit encodings do not apply if the
corresponding bit in the RCGCGPIO, SCGCGPIO, or DCGCGPIO
register is clear.

0x0 = GPIO port N is not powered and does not receive a clock. In
this case, the state of the module is not retained. This configuration
provides the lowest power consumption state.

0x1 = GPIO port N is powered but does not receive a clock. In this
case, the module is inactive.

11

P11

R/W

0x1

GPIO Port M Power Control. The Pn bit encodings do not apply if the
corresponding bit in the RCGCGPIO, SCGCGPIO, or DCGCGPIO
register is clear.

0x0 = GPIO port M is not powered and does not receive a clock. In
this case, the state of the module is not retained. This configuration
provides the lowest power consumption state.

0x1 = GPIO port M is powered but does not receive a clock. In this
case, the module is inactive.

Содержание SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды