Texas Instruments SimpleLink CC2652PSIP, Руководство пользователя, Страница: 17 / 68

8.12 Zigbee and Thread - IEEE 802.15.4-2006 2.4 GHz (OQPSK DSSS1:8, 250 kbps) - RX
Measured on the CC2652xSIP-EM reference design with T
c
= 25 °C, V
DDS
= 3.0 V, f
RF
= 2440 MHz with
DC/DC enabled and high power PA connected to V
DDS
unless otherwise noted.
All measurements are performed at the antenna input with a combined RX and TX path, except for high power PA which is
measured at a dedicated antenna connection. All measurements are performed conducted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
General Parameters
Receiver sensitivity PER = 1% –98 dBm
Receiver saturation PER = 1% > 5 dBm
Adjacent channel rejection
Wanted signal at –82 dBm, modulated interferer at ±5 MHz,
PER = 1%
36 dB
Alternate channel rejection
Wanted signal at –82 dBm, modulated interferer at ±10 MHz,
PER = 1%
57 dB
Channel rejection, ±15 MHz or more
Wanted signal at –82 dBm, undesired signal is IEEE
802.15.4 modulated channel, stepped through all channels
2405 to 2480 MHz, PER = 1%
59 dB
Blocking and desensitization,
5 MHz from upper band edge Wanted signal at –97 dBm (3 dB above the sensitivity level),
CW jammer, PER = 1%
57 dB
Blocking and desensitization,
10 MHz from upper band edge Wanted signal at –97 dBm (3 dB above the sensitivity level),
CW jammer, PER = 1%
62 dB
Blocking and desensitization,
20 MHz from upper band edge Wanted signal at –97 dBm (3 dB above the sensitivity level),
CW jammer, PER = 1%
62 dB
Blocking and desensitization,
50 MHz from upper band edge Wanted signal at –97 dBm (3 dB above the sensitivity level),
CW jammer, PER = 1%
65 dB
Blocking and desensitization,
–5 MHz from lower band edge Wanted signal at –97 dBm (3 dB above the sensitivity level),
CW jammer, PER = 1%
59 dB
Blocking and desensitization,
–10 MHz from lower band edge Wanted signal at –97 dBm (3 dB above the sensitivity level),
CW jammer, PER = 1%
59 dB
Blocking and desensitization,
–20 MHz from lower band edge Wanted signal at –97 dBm (3 dB above the sensitivity level),
CW jammer, PER = 1%
63 dB
Blocking and desensitization,
–50 MHz from lower band edge Wanted signal at –97 dBm (3 dB above the sensitivity level),
CW jammer, PER = 1%
65 dB
Spurious emissions, 30 MHz to 1000
MHz
Measurement in a 50-Ω single-ended load –66 dBm
Spurious emissions, 1 GHz to 12.75
GHz
Measurement in a 50-Ω single-ended load –53 dBm
Frequency error tolerance
Difference between the incoming carrier frequency and the
internally generated carrier frequency
> 350 ppm
Symbol rate error tolerance
Difference between incoming symbol rate and the internally
generated symbol rate
> 1000 ppm
RSSI dynamic range 95 dB
RSSI accuracy ±4 dB
www.ti.com
CC2652PSIP
SWRS263A – FEBRUARY 2021 – REVISED JUNE 2022
Copyright © 2022 Texas Instruments Incorporated Submit Document Feedback 17
Product Folder Links: CC2652PSIP