manualshive.com logo in svg

Texas Instruments OMAP5910, Техническое справочное руководство


Поделиться
Скачать
background image

Frame Adjustment Counter

7-203

MPU Public Peripherals

The frame-adjustment counter register (FARC) is programmed with the
number of frame synchronization counts over which the frame start pulses are
counted. This is a 16-bit programmable fixed reference in the range of
0-65536. A value of zero disables the count operation.

Table 7–147. Frame Adjustment Reference Count Register (FARC)

Bit

Name

Function

Reset

Value

15–0

FARC

16-bit value in the range 0-65536: 0 = disable counting

0

The frame-start count register (FSC) is a 16-bit read-only register that contains
the number of frame-start rising edges that occur during the programmable
FARC period. The frame start counting can be in two modes. When the CNT
bit in the control and configuration register (CTRL) is set to one, the counting
is in continuous mode and this register is periodically updated (every time the
frame adjustment reference count is met) with the new count value. If CNT is
zero, the counting is in halt mode. The frame-start count register is updated
when the frame adjustment reference count is met, and the counting halts until
the software reads the FSC register.

A level-sensitive interrupt can be generated to indicate that the frame-start
counting is finished, and the FSC register is loaded with a new count value.
The interrupt is controlled by the INT_ENABLE bit in the control and configura-
tion register (CTRL). If this bit is set to one, an interrupt is generated when the
FSC register is updated. Since the interrupt is level-sensitive, the interrupt sig-
nal is kept low until the software reads the FSC register or the RUN bit in the
control register is set to zero. When the FSC is read or RUN bit in control regis-
ter is set to zero, the interrupt signal is reset to one. When in IN_ENABLE bit
is set to zero, no interrupt is generated. The interrupt can be enabled or
disabled for both continuous mode and halt mode.

Table 7–148. Frame Start Count Register (FSC)

Bit

Name

Function

Reset

Value

15–0

FS

16-bit value

0

Содержание OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP5910

3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Бренд: 3Com Страницы: 204
Ubiquiti U5-24-500W Quick Start Manual preview
U5-24-500W
Бренд: Ubiquiti Страницы: 23
Tektronix CTS 850 User Manual preview
CTS 850
Бренд: Tektronix Страницы: 178
Ubiquiti PBE-5AC-300-ISO Quick Start Manual preview
PBE-5AC-300-ISO
Бренд: Ubiquiti Страницы: 28
ICP DAS USA PISO-725 Series Quick Start Manual preview
PISO-725 Series
Бренд: ICP DAS USA Страницы: 8
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Бренд: Infoblox Страницы: 13
Sans Digital ELITENAS EN104L+(B) Quick Installation Manual preview
ELITENAS EN104L+(B)
Бренд: Sans Digital Страницы: 9
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual preview
Acme Packet 3900
Бренд: Oracle Страницы: 70
Thecus 1U4600 User Manual preview
1U4600
Бренд: Thecus Страницы: 148
Crestron QM-IEM Installation Manual preview
QM-IEM
Бренд: Crestron Страницы: 8
SIIG Serial ATA PCI RAID Quick Installation Manual preview
Serial ATA PCI RAID
Бренд: SIIG Страницы: 36
Arista CloudVision DCA-CV-100 Quick Start Manual preview
CloudVision DCA-CV-100
Бренд: Arista Страницы: 46
NETGEAR AirBridge WBC502 User Manual preview
AirBridge WBC502
Бренд: NETGEAR Страницы: 7
Lenze L-force MC-PNC Mounting Instructions preview
L-force MC-PNC
Бренд: Lenze Страницы: 46
StarTech.com SATSASTRX25 Manual preview
SATSASTRX25
Бренд: StarTech.com Страницы: 7
AvaLAN AW5802mTR-EVAL User Manual preview
AW5802mTR-EVAL
Бренд: AvaLAN Страницы: 13
Bolide BN-NVR/32NX User Manual preview
BN-NVR/32NX
Бренд: Bolide Страницы: 80
WTI RSM Series User Manual preview
RSM Series
Бренд: WTI Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды