manualshive.com logo in svg

Texas Instruments OMAP5910, Техническое справочное руководство


Поделиться
Скачать
background image

Introduction

 

2-2

2.1

Introduction

The MPU of the OMAP5910 device controls the memory management units
(MMUs), the system direct memory access (DMA) controller, the MPU TI
peripheral bus (TIPB) bridge, and peripherals.

Figure 2–1 shows the OMAP5910 device with the MPU subsystem high-
lighted. The subsystem contains the following components:

-

MPU core (see Section 2.2, MPU Core)

-

Traffic controller (see Chapter 4, Memory Interface Traffic Controller)

-

MPU MMU (see Section 2.7, MPU Memory Management Unit)

-

DSP MMU (see Section 2.8, DSP Memory Management Unit)

-

System DMA controller (see Chapter 5, System DMA Controller)

-

LCD controller (see Chapter 11, LCD Controller)

-

MPU TIPB bridge (see Section 2.10, MPU TI Peripheral Bus Bridges)

-

Clock manager (see Chapter 15, Clock Generation and System Reset
Management)

-

Interrupt handler (see Section 6.4.1, MPU Level 1 Interrupt Handler,
Section 6.4.2, MPU Level 2 Interrupt Handler, and Section 8.4, [DSP]
Interrupt Handlers)

-

Timers (see Section 6.2, [MPU] Timer Description and Section 8.2, [DSP]
Timers)

-

Watchdog timer (see Section 6.3, [MPU] Watchdog Timer and Section 8.3,
[DSP] Watchdog Timer)

-

Interprocessor 

communication (see Section 10.2, Interprocessor

Communication)

-

1.5M-bit SRAM internal memory

Содержание OMAP5910


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP5910

C4i U1000 User Manual preview
U1000
Бренд: C4i Страницы: 8
Lattice Semiconductor CrossLink-NX Quick Start Manual preview
CrossLink-NX
Бренд: Lattice Semiconductor Страницы: 15
Lattice Semiconductor iCE40 UltraLite Usage Manual preview
iCE40 UltraLite
Бренд: Lattice Semiconductor Страницы: 13
Xilica Audio Design XP 4080 User Manual preview
XP 4080
Бренд: Xilica Audio Design Страницы: 30
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Бренд: B&B Electronics Страницы: 4
CAP-XX Purpose User Manual preview
Purpose
Бренд: CAP-XX Страницы: 8
IDT DBP 7+4 User Manual preview
DBP 7+4
Бренд: IDT Страницы: 93
ACTi GNR-310 Quick Installation Manual preview
GNR-310
Бренд: ACTi Страницы: 12
SSV Embedded Systems eSOM/3517 Hardware Reference Manual preview
eSOM/3517
Бренд: SSV Embedded Systems Страницы: 17
Xyclop XC-4CH-NVR-1TB User Manual preview
XC-4CH-NVR-1TB
Бренд: Xyclop Страницы: 144
Silvertel Ag102 User Manual preview
Ag102
Бренд: Silvertel Страницы: 9
BIIZZY zoomno MSC-5578 Setup Instructions preview
zoomno MSC-5578
Бренд: BIIZZY Страницы: 2
Navitar 1-62643 Dimensional Drawing preview
1-62643
Бренд: Navitar Страницы: 1
CopperOptics 150-1342-01 Manual preview
150-1342-01
Бренд: CopperOptics Страницы: 12
Inspired Energy ATA004N Operating Instructions preview
ATA004N
Бренд: Inspired Energy Страницы: 5
ExtraHop 72 TB ESU Quick Start Manual preview
72 TB ESU
Бренд: ExtraHop Страницы: 3
Valcom VIP-814 Installation Manual preview
VIP-814
Бренд: Valcom Страницы: 3
8e6 Technologies Threat Analysis Reporter TAR Quick Start Manual preview
Threat Analysis Reporter TAR
Бренд: 8e6 Technologies Страницы: 76

Бренды по названию

Популярные бренды

Загрузить еще бренды