manualshive.com logo in svg

Texas Instruments OMAP36 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Public Version

High-Speed USB Host Subsystem

www.ti.com

7

6

5

4

3

2

1

0

RESERVED

IDGND_RISE

SESSEND_RISE

SESSVALID_RISE

VBUSVALID_RISE

HOSTDISCONNECT_RISE

Bits

Field Name

Description

Type

Reset

7:5

RESERVED

Reserved

R

0x0

4

IDGND_RISE

Generate an interrupt event notification when IdGnd

RW

0x0

changes from low to high.
Event is automatically masked if the IdPullup bit is
cleared to 0 and for 50 ms after IdPullup is set to 1.
Write 0x0: No effect on bit value
Write 0x1: Clear the bit to 0

3

SESSEND_RISE

Generate an interrupt event notification when SessEnd

RW

0x0

changes from low to high.
Write 0x0: No effect on bit value
Write 0x1: Clear the bit to 0

2

SESSVALID_RISE

Generate an interrupt event notification when SessValid

RW

0x0

changes from low to high. SessValid is the same as
UTMI+ AValid.
Write 0x0: No effect on bit value
Write 0x1: Clear the bit to 0

1

VBUSVALID_RISE

Generate an interrupt event notification when VbusValid

RW

0x0

changes from low to high.
Write 0x0: No effect on bit value
Write 0x1: Clear the bit to 0

0

HOSTDISCONNECT_RISE

Generate an interrupt event notification when

RW

0x0

Hostdisconnect changes from low to high. Applicable only
in host mode (DpPulldown and DmPulldown both set to
1b).
Write 0x0: No effect on bit value
Write 0x1: Clear the bit to 0

Table 22-105. Register Call Summary for Register ULPI_USB_INT_EN_RISE_CLR_i

High-Speed USB Host Subsystem

•

High-Speed USB Host Subsystem Register Summary

:

[0]

Table 22-106. ULPI_USB_INT_EN_FALL_i

Address Offset

0x0000 0010 + (0x100 * i)

Index

i = 0 to 2

Physical Address

0x4806 2810 + (0x100 * i)

Instance

USBTLL

Description

Enables an interrupt event notification when the corresponding status bit changes from high to low. By
default, all transitions are enabled. Read/Write address.

Type

RW

3308

High-Speed USB Host Subsystem and High-Speed USB OTG Controller

SWPU177N – December 2009 – Revised November 2010

Copyright © 2009–2010, Texas Instruments Incorporated

Содержание OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP36 Series

D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Бренд: D-Link Страницы: 31
Tripp Lite N48M Series Installation Manual preview
N48M Series
Бренд: Tripp Lite Страницы: 20
LogLogic LX 1010 Quick Start Manual preview
LX 1010
Бренд: LogLogic Страницы: 30
Analog Devices EZ-Extender Analog 120-Pin Probing Board Manual preview
EZ-Extender Analog 120-Pin Probing Board
Бренд: Analog Devices Страницы: 29
Orolia Seven Solutions WR-ZEN Series User Manual preview
Seven Solutions WR-ZEN Series
Бренд: Orolia Страницы: 167
ZyXEL Communications ZyXEL ZyAIR B-120 Quick Installation Manual preview
ZyXEL ZyAIR B-120
Бренд: ZyXEL Communications Страницы: 20
MICROENER IM30-CV Operation Manual preview
IM30-CV
Бренд: MICROENER Страницы: 24
Intel 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU User Manual preview
640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU
Бренд: Intel Страницы: 105
Vega ARIES v3.0 Product Reference Manual preview
ARIES v3.0
Бренд: Vega Страницы: 12
IEI Technology WAFER-ULT4 User Manual preview
WAFER-ULT4
Бренд: IEI Technology Страницы: 136
V-Count Ultima Go Quick Installation Manual preview
Ultima Go
Бренд: V-Count Страницы: 2
Digi DataFire GO! PRO Manual preview
DataFire GO! PRO
Бренд: Digi Страницы: 20
Kontron AdvancedTCA AT8901M User Manual preview
AdvancedTCA AT8901M
Бренд: Kontron Страницы: 76
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Бренд: IEI Technology Страницы: 142
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Бренд: RadioSPECTRAL Страницы: 2
ZALMAN VF2000 LED User Manual preview
VF2000 LED
Бренд: ZALMAN Страницы: 9
Ultra Products Internal All-in-One Digital Media Drive ULT31793 Specifications preview
Internal All-in-One Digital Media Drive ULT31793
Бренд: Ultra Products Страницы: 1
R.V.R. Elettronica PTX30-UHT Installation, Technical And Maintenance Manual preview
PTX30-UHT
Бренд: R.V.R. Elettronica Страницы: 171

Бренды по названию

Популярные бренды

Загрузить еще бренды