manualshive.com logo in svg

Texas Instruments MSP430x11x1, Техническое описание


Поделиться
Скачать
background image

MSP430x11x1

MIXED SIGNAL MICROCONTROLLER

SLAS241C – SEPTEMBER 1999 – REVISED JUNE 2000

1

POST OFFICE BOX 655303 

•

 DALLAS, TEXAS 75265

D

Low Supply Voltage Range 1.8 V – 3.6 V

D

Ultralow-Power Consumption
Low Operation Current, 
  1.3 

µ

A at 4 kHz, 2.2 V

  160 

µ

A at 1 MHz, 2.2 V

D

Five Power Saving Modes:
  (Standby Mode: 0.8 

µ

A,

  RAM Retention Off Mode: 0.1 

µ

A)

D

Wake-Up From Standby Mode in 6 

µ

s

D

16-Bit RISC Architecture, 125 ns 
Instruction Cycle Time

D

Basic Clock Module Configurations:
–  Various Internal Resistors
–  Single External Resistor
–  32 kHz Crystal
–  High Frequency Crystal
–  Resonator
–  External Clock Source

D

16-Bit Timer With Three Capture/Compare
Registers

D

Slope A/D Converter With External
Components

D

On-Chip Comparator for Analog Signal
Compare Function or Slope A/D
Conversion

D

Serial Onboard Programming

D

Programmable Code Protection by Security
Fuse (C11x1 Only)

D

Family Members Include:
MSP430C1111: 2KB ROM, 128B RAM
MSP430C1121: 4KB ROM, 256B RAM
MSP430F1101: 1KB + 128B Flash Memory

(MTP

{

), 128B RAM

MSP430F1121: 4KB + 256B Flash Memory

(MTP

{

), 256B RAM

D

Available in a 20-Pin Plastic Small-Outline
Wide Body (SOWB) Package and 20-Pin
Plastic Thin Shrink Small-Outline Package
(TSSOP)

     

description

The Texas Instruments MSP430 series is an ultralow-power microcontroller family consisting of several devices
featuring different sets of modules targeted to various applications. The microcontroller is designed to be battery
operated for an extended-application lifetime. With 16-bit RISC architecture, 16 bit integrated registers on the
CPU, and a constant generator, the MSP430 achieves maximum code efficiency. The digitally-controlled
oscillator provides fast wake-up from all low-power modes to active mode in less than 6 

m

s.

Typical applications include sensor systems that capture analog signals, convert them to digital values, and then
process the data and display them or transmit them to a host system. Stand alone RF sensor front end is another
area of application. The I/O port inputs provide single slope A/D conversion capability on resistive sensors. The
MSP430x11x series is an ultralow-power mixed signal microcontroller with a built in 16-bit timer and fourteen
I/O pins. The MSP430x11x1 family adds a versatile analog comparator.

The flash memory provides added flexibility of in-system programming and data storage without significantly
increasing the current consumption of the device. The programming voltage is generated on-chip, thereby
alleviating the need for an additional supply, and even allowing for reprogramming of battery-operated systems.

{

MTP = Multiple Time Programmable

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

Copyright 

 2000, Texas Instruments Incorporated

PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.

1
2
3
4 
5
6
7
8
9
10

20
19
18
17
16
15
14
13
12

11

TEST

VCC

P2.5/R

osc

V

SS

XOUT

XIN

RST/NMI

P2.0/ACLK

P2.1/INCLK

P2.2/CAOUT/TA0

P1.7/TA2/TDO/TDI
P1.6/TA1/TDI
P1.5/TA0/TMS
P1.4/SMCLK/TCK
P1.3/TA2
P1.2/TA1
P1.1/TA0
P1.0/TACLK
P2.4/CA1/TA2
P2.3/CA0/TA1

DW OR PW PACKAGE

(TOP VIEW)

Содержание MSP430x11x1














































Отзывы:

Нет отзывов

Похожие инструкции для MSP430x11x1

ZALMAN CNPS17X User Manual preview
CNPS17X
Бренд: ZALMAN Страницы: 20
Teagle Tomahawk 7100 Operator'S Manual preview
Tomahawk 7100
Бренд: Teagle Страницы: 40
Compaq Proliant 800 Setup And Installation Manual preview
Proliant 800
Бренд: Compaq Страницы: 112
AMD SB710 User Manual preview
SB710
Бренд: AMD Страницы: 20
Lucent Technologies PARTNER Voice Messaging PC Card Release 2 Installation And Programming preview
PARTNER Voice Messaging PC Card Release 2
Бренд: Lucent Technologies Страницы: 67
Element14 Wireless Connectivity Cape Quick Start Manual preview
Wireless Connectivity Cape
Бренд: Element14 Страницы: 2
Atmel STK501 Specification Sheet preview
STK501
Бренд: Atmel Страницы: 2
Commell FS-A79 User Manual preview
FS-A79
Бренд: Commell Страницы: 36
Compal KALA0 Schematics Document preview
KALA0
Бренд: Compal Страницы: 47
UNICORECOMM UM620N User Manual preview
UM620N
Бренд: UNICORECOMM Страницы: 19
Neousys Technology PCIe-USB381F User Manual preview
PCIe-USB381F
Бренд: Neousys Technology Страницы: 24
swiftech MCW5000-64RH Installation Manual preview
MCW5000-64RH
Бренд: swiftech Страницы: 2
ICP ICP9014RO Installation And User Manual preview
ICP9014RO
Бренд: ICP Страницы: 142
Microscan MS-96 Vial Reader User Manual preview
MS-96 Vial Reader
Бренд: Microscan Страницы: 67
Honeywell Home LTEM-PA Installation And Setup Manual preview
LTEM-PA
Бренд: Honeywell Home Страницы: 36
Roland Symphonique Strings SRX-04 Owner'S Manual preview
Symphonique Strings SRX-04
Бренд: Roland Страницы: 12
Alpine PXE-R600 Manual preview
PXE-R600
Бренд: Alpine Страницы: 17
Promax NGM EVO User Manual preview
NGM EVO
Бренд: Promax Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды