Texas Instruments LP8861-Q1 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 25

Texas Instruments LP8861-Q1 Скачать руководство пользователя страница 4

User's Guide

SNVU456 – July 2015

LP8861-Q1EVM Evaluation Module

1

Preface

1.1

About this Manual

This user’s guide describes the module used to evaluate characteristics, operation, and use of the
LP8861-Q1 low EMI, high-performance 4-channel LED driver for automotive lighting. This document
includes a schematic diagram, PCB layout, and bill of materials (BOM).

1.2

Related Documentation from Texas Instruments

LP8861-Q1 data sheet

1.3

FCC Warning

This equipment is intended for use in a laboratory test environment only. It generates, uses, and can
radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonable
protection against radio frequency interference. Operation of this equipment in other environments may
cause interference with radio communications, in which case the user, at their own expense, will be
required to take whatever measures may be required to correct this interference.

1.4

If You Need Assistance

Contact your local TI sales representative.

2

Introduction

The Texas Instruments LP8861-Q1EVM evaluation module (EVM) helps designers to evaluate the
operation and performance of the LP8861-Q1 device. The LP8861-Q1EVM uses the LP8861-Q1 to drive
up to 4 LED strings for LCD backlighting with high efficiency. Information about output voltage and current
ratings of the LP8861-Q1 can also be found in the device data sheet (

A power supply connection for the VIN and test points for each signal can be found on the evaluation
board. A separate LED board can be used as a load; it is also possible to connect LCD panel to the output
connectors.

For evaluation purposes, the EVM has been tested over a 4.5-V to 40-V input range. This voltage range is
within the recommended operating range for input voltage of the LP8861-Q1. Users are cautioned to
evaluate their specific operating conditions and choose components with the appropriate voltage ratings
before designing this circuitry into a final product.

4

LP8861-Q1EVM Evaluation Module

SNVU456 – July 2015

Submit Documentation Feedback

Copyright © 2015, Texas Instruments Incorporated

«
...
2
3
4
5
6
...
»

Содержание LP8861-Q1


























Отзывы:

Нет отзывов