Texas Instruments LM36923HEVM Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 29

Texas Instruments LM36923HEVM Скачать руководство пользователя страница 7

12 series LED

2 series LED

4 series LED

6 series LED

8 series LED

10 series LED

12 series LED

OUT

LED String

Disconnected

OUT

LED+

LED+

LED String

Connected

Setup

7

SNVU509 – January 2016

Submit Documentation Feedback

Copyright © 2016, Texas Instruments Incorporated

LM36923HEVM User's Guide

Figure 4. OUT Jumper Settings

HL1, HL2, HL3 -

This connector provides a star connection to the LED string allowing the user to

configure the LED string for 1, 2, 3, 4, 5 or 6 series dual-LEDs.

Figure 5. HL1, HL2, HL3 star jumper configuration settings

ODD1, ODD2, ODD3 -

These connectors provide a method for inserting a single LED in each string.

When the jumper is removed from ODD1, ODD2 ,ODD3 the single LED D107, D207, D307 is part of the
respective LED string. When a jumper is inserted on ODD1, ODD2, ODD3 the single LED D107, D207,
D307 is bypassed in the respective LED string.

ILED1, ILED2, ILED3 -

The LM36923HEVM provides a way to accurately measure the LED current

through each LED string on board. Resistors RL1 , RL2 and RL3 (10

Ω

) are placed between the cathode

of last LED in each respective string and the LM36923H Current Sink Output.

2.2

Setup

The input voltage range for the backlight driver is 2.5 volts to 5.5 volts. The on-board LEDs or an LED
module should be connected for proper operation.

2.3

Operation

For proper operation of the LM36923HEVM, the jumpers should be properly configured. The
recommended setting, using shorting blocks is:

ASEL to USB2ANY: install jumper between pins 2 and 4

VIO to VIN: install jumper between pins 2 and 3

VL to VIN: jumper installed

OUT to LED+: install jumper between pins 2 and 3.

PWM from USB2ANY: jumper installed

HL1, HL2, HL3: install jumper in position 3 for each string

ODD1, ODD2, ODD3: jumper installed (odd LED bypassed)

Using these settings the device will be configured for USB2ANY control with 2 dual-led (4 LEDs) per
string.

«
...
5
6
7
8
9
...
»

Содержание LM36923HEVM






























Отзывы:

Нет отзывов