Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 91

Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 48

Technical Reference Manual

TMDXEVM6657L

SPRUHG7 - Revised August 2012

TMDXEVM6657LE

Page 48 / 90

3.3 DIP and PushButton Switches

The C6657 Lite EVM has three push button switches and three sliding actuator DIP switches. The RST_COLD1,
RST_WARM1 and RST_FULL1 are push button switches while SW3, SW5 and SW9 are DIP switches. The
function of each of the switches is listed in the table below:

Table 3.17: C6657 Lite EVM Board Switches

Switch

Function

RST_COLD1

Cold Reset Event (RFU)

RST_FULL1

Full Reset Event

RST_WARM1 Warm Reset Event

SW3

DSP Configuration, DSP Boot mode

SW5

DSP Boot mode, PLL setting, PCIe
Mode Selection

SW9

PCIe Enable/ Disable, User Switch

3.3.1 RST_COLD1, Cold Reset

The button is reserved for future use.

3.3.2 RST_FULL1, Full Reset

Pressing the RST_FULL1 button switch will issue a RESETFULL# to TMS320C6657 by

FPGA. It‟ll reset DSP

and other peripherals.

3.3.3 RST_WARM1, Warm Reset

Pressing the RST_WARM1 button switch will issue a RESET# to TMS320C6657 by FPGA. The FPGA will assert
the RESET# signal to DSP and DSP will execute either a HARD or SOFT reset by the configuration in the
RSCFG register in PLLCTL.

Note:

Users may refer to the

TMS320C6657 Data Manual

to check the difference between assertion of DSP

RESET# and the other reset signals.

3.3.4 SW3, DSP Configuration

SW3 is an 8 position DIP switch, which is used for DSP configuration. A diagram of SW3 switch (with factory
default settings) is shown below:

8

9

7

10

6

11

5

12

4

13

3

14

2

15

1

16

Logic “1”

Switch OFF

Logic “0”

Switch ON

Figure 3.5: SW3 default settings

The following table describes the positions and corresponding function on SW3.

«
...
46
47
48
49
50
...
»

Содержание eInfochips TMDXEVM6657L




























































































Отзывы:

Нет отзывов