Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 91

Texas Instruments eInfochips TMDXEVM6657L Скачать руководство пользователя страница 14

Technical Reference Manual

TMDXEVM6657L

SPRUHG7 - Revised August 2012

TMDXEVM6657LE

Page 14 / 90

1.3 Basic Operation

The C6657 Lite EVM p

latform is designed to work with TI‟s Code Composer Studio (CCS) development

environment  and  ships  with  a  version  specifically  tailored  for  this  board.  CCS  can  interfaces  with the  board  via
on-board emulation circuitry using the USB cable supplied along with this EVM or through external emulator.

The  EVM  comes  with  the  Texas  Instruments  Multicore  Software  Development  Kit  (MCSDK)  for  SYS/BIOS  OS.
The BIOS MCSDK provides the core foundational building blocks that facilitate application software development
on TI's high performance and multicore DSPs. It also includes an out-of-box demonstration. Follow the instruction
in  BIOS  MCSDK  Getting  Started  Guide    to  install  all  the  necessary  development  tools,  drivers  and
documentation.

To  start  operating  the  board,  follow  instructions  in  the  Quick  Start  Guide.  This  guide  provides  instruction  for
proper  connections  and  configuration  for  running  the  POST  and  OOB  Demos.  After  completing  the  POST  and
OOB  Demos,  proceed  with  installing  CCS  and  the  EVM  support  files  by  following  the  instructions  on  the  DVD.
This process will install all the necessary development tools, drivers and documentation.

After the installation is completed, follow below steps to run Code Composer Studio.

1. Power ON the board using power brick adaptor (12V/2.5A) supplied along with this EVM or Insert this

EVM board into MicroTCA chassis or AMC carrier back-plane.

2. Connect USB cable from host PC to EVM board.
3. Launch Code Composer Studio from host PC by double clicking on its icon at PC desktop.

Detailed information about the EVM including examples and reference material is available in the DVD available
with this EVM kit.

Figure 1.3: TMDXEVM6657L

«
...
12
13
14
15
16
...
»

Содержание eInfochips TMDXEVM6657L




























































































Отзывы:

Нет отзывов