Texas Instruments DS280MB810EVM Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 28

Texas Instruments DS280MB810EVM Скачать руководство пользователя страница 21

EVM Cable Assemblies

21

SNLU213A – October 2016 – Revised September 2019

Submit Documentation Feedback

Copyright © 2016–2019, Texas Instruments Incorporated

DS280MB810EVM User’s Guide

8

EVM Cable Assemblies

The DS280MB810EVM uses Huber+Suhner 1x8 MXP cable assemblies. For Huber+Suhner quotes or
additional information requests, please contact:
[email protected]
HUBER+SUHNER Inc.
8530 Steele Creek Place Drive, Suite H
Charlotte-NC- 28273
+1 704-790-7300

Below are suggested part numbers that can be used with this EVM. Other part numbers and cable lengths
have not been tested, but can be considered for use.

1. 85014420, MF53/1x8A_21MXP/21SMA/152: “MXP-18 cable assembly”. This is a lower cost cable

assembly compared to the MXP-40, but the SI performance is very good and more than adequate for
25Gbps operation.

2. 84099607, MF53/1x8A_21MXP/11SK/305: “MXP-40 cable assembly”. This cable assembly is designed

specifically for 40+ GHz. It features a male cable end and longer cable length options.

3. 84098900, MF53/1x8A_21MXP/21SK_ergo/305: “MXP-40 cable assembly”. This cable assembly is

designed specifically for 40+ GHz. It features a female cable end and longer cable length options.

4. 84099634, MF53/1x8A_21MXP/21/MXP/305: "MXP-50 cable assembly". This cable assembly is

designed specifically for 50+ GHz. It features a MXP connections on both ends of the cable for board
bridging and longer cable length options.

«
...
19
20
21
22
23
...
»

Содержание DS280MB810EVM





























Отзывы:

Нет отзывов