manualshive.com logo in svg

Texas Instruments Concerto F28M35 Series, Техническое справочное руководство


Поделиться
Скачать
background image

System Control Registers

www.ti.com

284

SPRUH22I – April 2012 – Revised November 2019

Submit Documentation Feedback

Copyright © 2012–2019, Texas Instruments Incorporated

System Control and Interrupts

Table 1-178. CTOMIPCCLR Register Field Descriptions

Bit

Field

Value

Description

31

IPC32

0

CTOMIPCCLR Flag 32. C28 to M3 core IPC flag 32 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers

30

IPC31

0

CTOMIPCCLR Flag 31. C28 to M3 core IPC flag 31 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

29

IPC30

0

CTOMIPCCLR Flag 30. C28 to M3 core IPC flag 30 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

28

IPC29

0

CTOMIPCCLR Flag 29. C28 to M3 core IPC flag 29 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

27

IPC28

0

CTOMIPCCLR Flag 28. C28 to M3 core IPC flag 28 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

26

IPC27

0

CTOMIPCCLR Flag 27. C28 to M3 core IPC flag 27 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

25

IPC26

0

CTOMIPCCLR Flag 26. C28 to M3 core IPC flag 26 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

24

IPC25

0

CTOMIPCCLR Flag 25. C28 to M3 core IPC flag 25 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

23

IPC24

0

CTOMIPCCLR Flag 24. C28 to M3 core IPC flag 24 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

22

IPC23

0

CTOMIPCCLR Flag 23. C28 to M3 core IPC flag 23 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

21

IPC22

0

CTOMIPCCLR Flag 22. C28 to M3 core IPC flag 22 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

20

IPC21

0

CTOMIPCCLR Flag 21. C28 to M3 core IPC flag 21clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

19

IPC20

0

CTOMIPCCLR Flag 20. C28 to M3 core IPC flag 20 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

18

IPC19

0

CTOMIPCCLR Flag 19. C28 to M3 core IPC flag 19 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

17

IPC18

0

CTOMIPCCLR Flag 18. C28 to M3 core IPC flag 18 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

16

IPC17

0

CTOMIPCCLR Flag 17. C28 to M3 core IPC flag 17 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

15

IPC16

0

CTOMIPCCLR Flag 16. C28 to M3 core IPC flag 16 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers

14

IPC15

0

CTOMIPCCLR Flag 15. C28 to M3 core IPC flag 15 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

13

IPC14

0

CTOMIPCCLR Flag 14. C28 to M3 core IPC flag 14 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

12

IPC13

0

CTOMIPCCLR Flag 13. C28 to M3 core IPC flag 13 clear. If a bit is cleared by writing a ‘1’ then the
corresponding bit in CTOMIPCFLG is cleared. The status of this bit is not readable in this register –
it is readable in the CTOMIPCFLG and STS registers.

Содержание Concerto F28M35 Series
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Concerto F28M35 Series

wattio AIR Read Me preview
AIR
Бренд: wattio Страницы: 20
Samson 430 Series Mounting And Operating Instructions preview
430 Series
Бренд: Samson Страницы: 78
Rachio 3 Get Started preview
3
Бренд: Rachio Страницы: 16
Panasonic FP-I4C User Manual preview
FP-I4C
Бренд: Panasonic Страницы: 31
Panasonic EYFR03 Training Manual preview
EYFR03
Бренд: Panasonic Страницы: 31
NAiS FP Series Hardware Manual preview
FP Series
Бренд: NAiS Страницы: 199
Panasonic CZ-ANC2 Instruction Manual preview
CZ-ANC2
Бренд: Panasonic Страницы: 38
Panasonic CZ-256ESMC3 Quick Reference preview
CZ-256ESMC3
Бренд: Panasonic Страницы: 36
Panasonic CZ-256ESMC3 Technical Data Manual preview
CZ-256ESMC3
Бренд: Panasonic Страницы: 179
Panasonic AW-RP60G Operating Manual preview
AW-RP60G
Бренд: Panasonic Страницы: 23
Harpo BraillePen 12 Quick Start Manual preview
BraillePen 12
Бренд: Harpo Страницы: 35
Hardi HC 6500 Quick Manual preview
HC 6500
Бренд: Hardi Страницы: 2
HANYOUNG NUX NP100 Manual preview
NP100
Бренд: HANYOUNG NUX Страницы: 36
HANYOUNG NUX HY Series Instruction Manual preview
HY Series
Бренд: HANYOUNG NUX Страницы: 4
MADRIX Nebula User Manual preview
Nebula
Бренд: MADRIX Страницы: 91
MADRIX Nebula Quick Start Manual preview
Nebula
Бренд: MADRIX Страницы: 40
YASKAWA MP Series Driver Manual preview
MP Series
Бренд: YASKAWA Страницы: 18
Samwontech TEMP2000 Series Installation Manual preview
TEMP2000 Series
Бренд: Samwontech Страницы: 91

Бренды по названию

Популярные бренды

Загрузить еще бренды