Texas Instruments CC900DB Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 20

Texas Instruments CC900DB Скачать руководство пользователя страница 20

SWRU064

20

5

Using the Demonstrator Board as a prototype module

The purpose of the Demonstrator Board is to show a simple transceiver module with
battery supply and integrated PCB antenna. The demonstrator can be used “as is” for
simple range and coverage measurements. But keep in mind that this module use only 0
dBm and a small rather ineffective antenna. The range can be extended substantially
using more power and a better antenna.

The Demonstrator Board can also be used as a prototype module when developing your
own applications. You may:

•

Reprogram the EEPROM configuration data for your own system parameters. The
SmartRF® Studio generates the configuration data values. See section 2.5 for
EEPROM memory map.

•

Rewrite the microcontroller code to use the edge connector to interface your host
system

•

Insert a standard 2.54 mm pitch contact to interface a motherboard at the edge
connector.

•

Remove L8, and mount a coax connector at the antenna output. Thus an external
antenna could be used. The antenna should be matched to 50 Ohm

«
...
18
19
20

Содержание CC900DB





















Отзывы:

Нет отзывов