Texas Instruments CC1150 страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 66

background image

e.g 6

PA_POWER[2:0]
in FREND0 register

PATABLE(0)[7:0]

PATABLE(1)[7:0]

PATABLE(2)[7:0]

PATABLE(3)[7:0]

PATABLE(4)[7:0]

PATABLE(5)[7:0]

PATABLE(6)[7:0]

PATABLE(7)[7:0]

Index into PATABLE(7:0)

The PA uses this
setting.

Settings 0 to PA_POWER are
used during ramp-up at start of
transmission and ramp-down at
end of transmission, and for
ASK/OOK modulation.

The SmartRF

Studio software

should be used to obtain optimum
PATABLE settings for various
output powers.

TM

SWRS037B – JANUARY 2006 – REVISED MARCH 2015

5.15 Voltage Regulators

CC1150 contains several on-chip linear voltage regulators, which generate the supply voltage needed by
low-voltage modules. These voltage regulators are invisible to the user, and can be viewed as integral
parts of the various modules. The user must however make sure that the absolute maximum ratings and
required pin voltages in

and

are not exceeded.

Setting the CSn pin low turns on the voltage regulator to the digital core and start the crystal oscillator.
The SO pin on the SPI interface must go low before the first positive edge on the SCLK (setup time is

s

given in

).

If the chip is programmed to enter power-down mode (SPWD strobe issued), the power will be turned off
after CSn goes high. The power and crystal oscillator will be turned on again when CSn goes low.

The voltage regulator for the digital core requires one external decoupling capacitor. The voltage regulator
output should only be used for driving the CC1150.

5.16 Output Power Programming

The RF output power level from the device has two levels of programmability, as illustrated in

Firstly, the special PATABLE register can hold up to eight user selected output power settings. Secondly,
the 3-bit FREND0.PA_POWER value selects the PATABLE entry to use. This two-level functionality
provides flexible PA power ramp up and ramp down at the start and end of transmission, as well as ASK
modulation shaping. In each case, all the PA power settings in the PATABLE from index 0 up to the
FREND0.PA_POWER value are used.

The power ramping at the start and at the end of a packet can be turned off by setting
FREND0.PA_POWER to zero and then programming the desired output power to index 0 in the
PATABLE.

If OOK modulation is used, the logic 0 and logic 1 power levels shall be programmed to index 0 and 1
respectively.

contains recommended PATABLE settings for various output levels and frequency bands.

DN012

gives complete tables for the different frequency bands. Using PA settings from 0x61 to 0x6F is

not recommended.

contains output power and current consumption for default PATABLE setting

(0xC6).

PATABLE must be programmed in burst mode if you want to write to other entries than PATABLE[0]. See

Section 5.5.6

for PATABLE programming details.

Figure 5-16. PA_POWER and PATABLE

32

Detailed Description

Copyright © 2006–2015, Texas Instruments Incorporated

Submit Documentation Feedback

Product Folder Links:

«
...
30
31
32
33
34
...
»

Содержание CC1150



































































Отзывы:

Нет отзывов

Похожие инструкции для CC1150

Бренд: Campbell Страницы: 50

ECHOMAP Ultra Series

Бренд: Garmin Страницы: 4

Бренд: l-com Страницы: 6

Бренд: E+E Elektronik Страницы: 36

Бренд: Kogan Страницы: 8

STORM PRO C-4014

Бренд: Feniex Страницы: 13

Бренд: Evikon Страницы: 4

Бренд: M-system Страницы: 2

Centronic EasyControl EC415A-III

Бренд: Becker Страницы: 20

Бренд: Eddystone Broadcast Страницы: 42

Network Device TX-CTB

Бренд: AMX Страницы: 12

Бренд: H-ITT Страницы: 2

Бренд: Yaesu Страницы: 34

MR HH500 FLT BT

Бренд: Cobra Страницы: 2

Бренд: Cobra Страницы: 51

Бренд: ERECA Страницы: 15

Бренд: YOKOGAWA Страницы: 2

Бренд: Peavey Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды