Texas Instruments bq51010BEVM-764 Скачать руководство пользователя страница 5

Страница: 5 / 26

www.ti.com

Equipment and EVM setup

4.4.8

TP8 – Boot-1 Boot Capacitor

This bootstrap capacitor 1 drive connects to the integrated circuit (IC).

4.4.9

TP9 – Boot-2 Boot Capacitor

This bootstrap capacitor 2 drive connects to the IC.

4.4.10

TP10 – CHG Charge

This output signal indicates that the output current is being delivered to OUT, the open-drain output.

4.4.11

TP11 – AC1 IC input

This is the AC input to the IC from series capacitors.

4.4.12

TP12 – Rectified Voltage

The input AC voltage is rectified into unregulated DC voltage; additional capacitance is used to filter the
voltage before the regulator.

4.4.13

TP13, TP14, TP15 – GND

These are the ground test points.

4.4.14

TP16 – TS Temp Sensor

This is the connection point for external thermistor; see the data sheet for additional information.

4.4.15

TP17 – FET Open Detection (FOD)

Input for rectified power measurement, pin F2 of the IC.

4.4.16

TP18– ILIM

Programming pin for over current limit, pin G1 of the IC.

4.5

Pin Description of the IC

Table 2. Pin Description

PIN Number (WCSP)

bq51010B

A1, A2, A3, A4

PGND

B1, B2

AC2, AC2

B3, B4

AC1, AC1

BOOT2

C2, C3

RECT

BOOT1

D1, D2, D3, D4

OUT

COM2

CLMP2

CLMP1

COM1

TS/CTRL

FOD

AD-EN

CHG

SLUUAE3A – August 2013 – Revised December 2013

bq51010BEVM-764 Evaluation Module (WCSP Package)

Submit Documentation Feedback

Содержание bq51010BEVM-764



























Результаты поиска

Содержание bq51010BEVM-764

Отзывы:

Похожие инструкции для bq51010BEVM-764

Бренды по названию

Популярные бренды

Texas Instruments bq51010BEVM-764, Руководство пользователя

Результаты поиска

Содержание bq51010BEVM-764

Отзывы:

Похожие инструкции для bq51010BEVM-764

Бренды по названию

Популярные бренды