Texas Instruments bq51010BEVM-764 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 26

Texas Instruments bq51010BEVM-764 Скачать руководство пользователя страница 4

Equipment and EVM setup

4.3.1

JP1 – EN1 Enable 1

Not populated in this EVM (HPA764-005).

4.3.2

JP2 – EN2 Enable 2

Enable signal input that allows the system to assert wireless charging. If EN2 is set to low, wireless
charging is enabled unless AD voltage > 3.6 V. If EN2 is set to High, AD mode disabled, wireless charging
always enabled. Used when OTG plus wireless charging is active.

4.3.3

JP3 – TS Enable or Disable

This jumper enables the TS adjustment feature using R3. The disable position sets voltage at the TS pin
to a safe value. The default shorting jumper setting is disabled.

4.3.4

JP4 – Pull-Up to Out or Vz

EN2 pull-up can be powered from OUT or RECT. Vz is derived from RECT through a resistor and Zener
diode D2.

4.3.5

JP5 – Termination

This jumper along with R14 and R13 are not installed in HPA764-001-003-005.

4.3.6

JP6 – ILIM Fix or ADJ

Max output current is set by ILIM pin. In the FIX position, the current is set to a fixed value. In the ADJ
position the current is set by R16.

4.4

Test Point Descriptions

The test points are described in the following paragraphs.

4.4.1

TP1 – AD-EN

This push-pull driver for the external PFET connects the adapter and the output from the bq51010B.

4.4.2

TP2 – AC Input 2

This is the test point for measuring AC voltage applied to the EVM from the receiver coil.

4.4.3

TP3 – COM2 Communication 2 Drive

Communication driver signal, open-drain output connected to communication capacitor.

4.4.4

TP4 – AC Input 1

This is the test point for measuring AC voltage applied to the EVM from the receiver coil.

4.4.5

TP5 – CLMP 1

Overvoltage clamp driver signal, open-drain output is connected to OVP capacitor.

4.4.6

TP6 – CLMP 2

Overvoltage clamp drive signal, open-drain output is connected to OVP capacitor.

4.4.7

TP7 – OUT Output Voltage

This test point is the output voltage.

4

bq51010BEVM-764 Evaluation Module (WCSP Package)

SLUUAE3A – August 2013 – Revised December 2013

Submit Documentation Feedback

Copyright © 2013, Texas Instruments Incorporated

«
...
2
3
4
5
6
...
»

Содержание bq51010BEVM-764



























Отзывы:

Нет отзывов