Texas Instruments bq34110EVM-796 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

Texas Instruments bq34110EVM-796 Скачать руководство пользователя страница 8

Operation

8

SLUUBI1A – October 2016 – Revised July 2018

Submit Documentation Feedback

Copyright © 2016–2018, Texas Instruments Incorporated

bq34110EVM-796 Evaluation Module

3.2.1

Cell Configuration

The bq34110 operates in one of two modes for measuring battery voltage. Place jumpers on the J2 and
J5 headers to select the mode of operation. See the

EVM Connections

section.

For packs where the stack voltage is less than 5 V:

•

Enable Calibration Mode on the device by pressing the

CAL_TOGGLE

button on the Commands

panel. Verify that the

CAL_EN

flag is set in the

Manufacturing Status

register.

•

Update the

Flash Update OK Voltage

parameter on the Data Memory

Configuration

screen to

100mV (default is 2.8V). This parameter prevents flash updates when the measured voltage is below
this setting. This can later be updated to an appropriate voltage once the dividers are configured.

•

Set the

Number of Series Cells

parameter to the appropriate value on the Data Memory

Configuration

screen.

•

Reset the gauge using the

RESET

button on the

Commands

panel.

•

Calibrate the stack voltage. See the

section.

NOTE:

The EVM can support single cell applications, where the cell voltage can drop below 2.5 V,

by providing an external 3.3-V supply to power REGIN. For voltages below 2.5V, remove the
jumper from J2 – pins 3 and 4 (upper

≤

5-V jumper location) and apply a 3.3-V supply to the

REGIN test point.

For packs where the stack voltage is greater than 5 V:

•

Enable Calibration Mode on the device by pressing the

CAL_TOGGLE

button on the

Commands

panel. Verify that the

CAL_EN

flag is set in the

Manufacturing Status

register.

•

Update the

Flash Update OK Voltage

parameter on the Data Memory

Configuration

screen to

100mV (default is 2.8V). This parameter prevents flash updates when the measured voltage is below
this setting.

•

Set the

VEN_EN

bit to “1” in the

Pin Control Config

in Data Memory on the

Settings

screen. This

enables the external voltage divider on the EVM and disables the internal voltage divider. The VEN pin
will pulse to enable the external resistor divider only during a voltage measurement to save power.

•

Set the

Number of Series Cells

parameter to the appropriate value on the Data Memory

Configuration

screen.

•

Set the

Voltage Divider

parameter in Data Memory on the

Calibration

screen. This value should be

set based on the external resistor divider setting. (For example, use ~19,200 when the J5 header is set
to the 16V setting which divides the BAT+ voltage by 19.2).

•

Reset the gauge using the

RESET

button on the

Commands

panel.

•

Calibrate the stack voltage. See the

section.

«
...
6
7
8
9
10
...
»

Содержание bq34110EVM-796

























Отзывы:

Нет отзывов