Texas Instruments AM64 Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 56

background image

Table 3-18. Board ID Memory Header Information (continued)

Header

Field Name

Size (bytes)

Comments

DDR_INFO

TYPE

1

Length

2

offset to next header

DDR control

2

DDR Control Word

MAC_ADDR

TYPE

1

payload type

Length

2

Size of payload

MAC control

2

MAC header control word

MAC_adrs

192

MAC address of AM65x PRG2

END_LIST

TYPE

1

End Marker

3.4.9 Ethernet Interface

Three Ethernet PHYs terminated to RJ45 connectors with integrated magnetics is supported on the EVM.

Figure 3-18. Ethernet Interface - CPSW Domain

The first PHY (connected to RJ45 connector J14) is interfaced to the CPSW_RGMII1 port of the SoC. The
DP83867 PHY has been selected for this interface based on its ability to configure the Tx and Rx Delays. Since
the CPSW_RGMII1_RX port is also multiplexed with PRG0 signals, a mux is needed to select the path from the
SoC to this PHY (in CPSW mode) or to the HSE connector (PRG0 mode). The selection is done using a GPIO
from the 24 bit IO expander.

The second PHY (connected to stacked RJ45 connector J21B) is interfaced to the PRG1_RGMII2 port of the
SoC. This port is directly multiplexed with the CPSW_RGMII2 port. In order to select between CPSW and PRG
operation, we need to multiplex the MDIO MDC signals from each controller to this PHY and the mux shall be
controlled by a GPIO from IO expander. PRG1_RGMII2 is also internally multiplexed with PRG1_MII signals.
The objective of the PHY used to connect this port is that the PHY should support both RGMII and MII modes,
hence DP83869 (48 pin) PHY is selected.

System Description

SPRUIX0B – FEBRUARY 2021 – REVISED MARCH 2021

Submit Document Feedback

AM64x GP EVM User's Guide

31

Copyright © 2021 Texas Instruments Incorporated

«
...
29
30
31
32
33
...
»

Содержание AM64 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для AM64 Series

Бренд: D-Link Страницы: 38

Web Smart DES-1210-28P

Бренд: D-Link Страницы: 6

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 23

Express EtherNetwork DI-604

Бренд: D-Link Страницы: 7

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 97

Бренд: National Instruments Страницы: 17

Бренд: National Instruments Страницы: 9

Бренд: IBA Страницы: 29

Бренд: Barco Страницы: 121

Бренд: Zonet Страницы: 2

Бренд: WAGO Страницы: 48

Industrial Network Track OSI

Бренд: GarrettCom Страницы: 10

2410SA - Serial ATA RAID Controller

Бренд: Adaptec Страницы: 14

Бренд: Renesas Страницы: 76

PXI Express PXIe-1085 Series

Бренд: National Instruments Страницы: 89

Бренд: Sun Microsystems Страницы: 410

Бренд: Dell Страницы: 37

Бренд: Bosch Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды