Texas Equipment CSZ 5800, Руководство пользователя

Страница: 13 / 22

13
11. Tips and advices
See Fig. 6
Use the chainsaw only with secure footing. Hold the
chainsaw at the right-hand side of your body (Fig. A).
The chain must be running at full speed before it makes
contact with the wood. Use the claw stop (lower tooth)
to secure the saw onto the wood before starting to cut.
Use the claw stop (a) as a leverage point while cutting
(Fig. B).
Do not operate the chainsaw with arms fully extended
or attempt to saw areas which are difficult to reach, or
on a ladder. Never use the chainsaw above shoulder
height (Fig. C).
12. Maintenance
Before any service and maintenance is done,
the power must be disconnected, it means the
battery removed from the tool.
•
Remove the battery before you clean and store the
machine.
•
For obtaining the best cutting results the chain and
guide bar must be cleaned and oiled regularly.
Remove dirt with a brush and oil lightly.
•
Use biodegradable oil.
•
Clean the housing and other parts with a mild
cleanser and a moist cloth. Never use aggressive
cleansers or solvents.
•
Prevent water from getting into the machine.
•
Use the guide bar cover when the machine is
stored.
Lubrication hole . Remove the guide bar and check
that the lubrication hole (1) is not blocked with
sawdust or dirt. Lubricate with oil/grease.’
Guide bar . Clean the nose wheel and chain groove
of any dirt. If required, turn the guide bar over to
evenly share wear. A worn guide bar can be
hazardous to use and should therefore be replaced.
Chain . The chain should be filed regularly to ensure
the best result.
1. Ensure that the guide bar is securely attached.
2.
Use a 4.0 mm (3/8”) round file (not supplied).
3. File all of the teeth with 3-4 strokes, so that they
are uniform, as shown in the illustration.
4. The height of the teeth must be checked regularly,
and if they are too high, they must be filed down
using a flat file (not supplied).
Replacing saw chain / guide bar
Replace chain when cutters are too worn to sharpen or
when chain breaks. Only use replacement chain type
91P062X (art. no. 441948).
Inspect guide bar before sharpening or replacing chain.
A worn or damaged guide bar is unsafe and should be
replaced. A worn or damaged guide bar will damage the
chain. It will also make cutting harder.
13. Specifications
Model CSZ 5800
Battery type Lithium Ion
Battery nominal voltage 58V
Battery rated voltage 50.4V
Motor power 1800W (brushless)
Chain speed 11.2 m/s
Guide bar length 45 cm
Chain oil capacity 200 ml
Net weight (tool only) 3.8 kg
14. Warranty terms and conditions
The warranty period is 2 years for private end users in
EU countries. Products sold for commercial use, only
have a warranty period of 1 year.
The warranty covers material and/or fabrication faults.
Restrictions and requirements
Normal wear and replacement of wearing parts are
NOT covered by the warranty.
Wearing parts, which are NOT covered for more than
12 months:
•
Guide bar
•
Chain
•
Battery: If the battery is not stored correct (frost-
free and recharged every 3 months), the durability
is only guaranteed for 6 months.
If you start the chainsaw without adding chain oil, the
guide bar and chain will be damaged and cannot be
repaired and therefore not covered by the warranty.
The warranty does NOT cover damages/faults
caused by:
•
Lack of service and maintenance
•
Structural changes
•
Exposure to unusual external conditions
•
If the machine has been improperly used or
overloaded
•
Wrong use of oil, gasoline or other liquid types,
which are not recommended in this user manual
•
Use of unoriginal spare parts.
•
Other conditions where Texas cannot be held
responsible.
Whether a case is a warranty claim or not is
determined in each case by an authorized service
center. Your receipt is your warranty note, why it
should always be kept safe.
REMEMBER: The purchase of spare parts as well as
any request for warranty repair, art. number (e.g.
900700XX), year and serial number should always be
informed.
* We reserve the right to change the conditions and
accept no liability for any misprints.