Testomat CL Скачать руководство пользователя

Страница: 23 / 52

Adjusting parameters in the device

Exiting selection mode



Press the RESET key to exit selection mode.

How to proceed after reset

The software is loaded again after the reset, and the device car-
ries out ventilation prior to analysis.

Start of measurements

Once you have completed the steps in the

Commissioning

section,

you can supply the device with power.



Switch on the device.

In interval operation (continuous operation) the measurement starts
automatically after 15 seconds.

In measurement phase mode, the first measurement is started after a
signal on the stop/start input.

Other functions in selection mode

Importing basic programming data from the SD card into the de-
vice



Press the

Manual

function key.



Press the

100%

function key.



Press the BOOT key.
The yellow LED next to the SD card lights up briefly.

The device then returns to normal interval operation.

Exporting basic programming data from the device onto the SD
card



Press the

Alarm

function key.



Press the

100%

function key.



Press the BOOT key.

The red LED next to the SD card lights up briefly.

The device then returns to normal interval operation.

Resetting to factory settings



Press the

100%

key.



Press the BOOT key.

The device then returns to normal interval operation.

press

NOTE

press

Содержание CL





















































Результаты поиска

Содержание CL

Отзывы:

Похожие инструкции для CL

Бренды по названию

Популярные бренды

Testomat CL, Руководство по эксплуатации

Результаты поиска

Содержание CL

Отзывы:

Похожие инструкции для CL

Бренды по названию

Популярные бренды