Tesla Gen 3 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 42

Tesla Gen 3 Скачать руководство пользователя страница 34

DISPUTE RESOLUTION

Tesla requires that you first provide written notification of any manufacturing defect within a reasonable
time, and within the applicable coverage period specified in this Charging Equipment Limited Warranty, and
allow Tesla an opportunity to make any needed repairs before submitting a dispute to our dispute
settlement program (described below). Please send written notification on dispute resolution to the
following address:

Vehicles registered in the UK:

Tesla Motors Ltd

Company number: 04384008

197 Horton Road, West Drayton

England, UB7 8JD

Please include the following information:

•  Tesla Part Number and Serial Number
•  Your name and contact information
•  Name and location of the Tesla Store and/or Tesla Service Center nearest to you
•  Description of the defect
•  History of the attempts you have made with Tesla to resolve the concern, or of any repairs or services

that were not performed by Tesla

• In the event any disputes, differences, or controversies arise between you and Tesla related to this

Charging Equipment Limited Warranty, Tesla will explore all possibilities for an amicable settlement

33

Gen 3 Wall Connector Manual

«
...
32
33
34
35
36
...
»

Содержание Gen 3











































Отзывы:

Нет отзывов