Tesco DTS-2990 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 45

Tesco DTS-2990 Скачать руководство пользователя страница 40

CONFIGURATIONS

33

www.tescometering.com

+1 215 785 2338

[email protected]

6.3

Disconnect Test

SCREEN

STEPS

1.

From the MAIN MENU, press

to access TEST

SELECTION.

2.

Press

to enter DISCONNECT TEST. The green

DISCONNECT TEST indicator will turn on.

3.

Press

to enable service voltage to socket.

4.

Optional: To set load current, press

to

highlight load current data box and enter desired
value.

5.

Optional: Press

to enable load current.

Note: BACKVOLTAGE will enable automatically.

6.

Once voltage is applied, and the meter service
disconnect is closed, the red JAW HOT indicators
will turn on. Refer to

Figure 6.3.1

.

NOTE:

For Form 1S, the JAW4 HOT indicator will

not turn on.

7.

Open  the  meter  service  disconnect.  If  successful,
the  JAW  HOT  indicators,  LOAD  current  and
BACKVOLTAGE  (if  enabled)  will  all  turn  off.  Refer
to

Figure 6.3.2

.

8.

If BACKVOLTAGE is turned on separate from LOAD,
it  will  not  turn  off  automatically  if  the  meter
disconnect  is  opened.  BACKVOLTAGE  can  be
turned  on  while  a  meter  disconnect  is  opened.  If
BACKVOLTAGE  is  on,  but  the  meter  disconnect  is
open, the JAW HOT indicator lights will turn on.

DISCONNECT

JAW 2

HOT

JAW 4

HOT

TEST

DISCONNECT

JAW 2

HOT

JAW 4

HOT

TEST

Figure 6.3.1-Disconnect

test in enabled state.

Figure 6.3.2-Successful

disconnect test.

«
...
38
39
40
41
42
...
»

Содержание DTS-2990














































Отзывы:

Нет отзывов