background image

CONTENTS

Title                                                                                   Page

1. INTRODUCTION ..............................................................................1

2. FEATURES .......................................................................................2

3. SPECIFICATIONS ............................................................................2

4. PARTS & CONTROLS .....................................................................4

4-1 Description of Parts & Control keys............................................4
4-2 Description of Display.................................................................8

5. OPERATING INSTRUCTIONS.......................................................10

5-1 Setting the Calibration Factor ...................................................10
5-2 luminous Flux Measurement ....................................................11
5-3 Maximum & Minimum Recording Measurement ......................12
5-4 Hold Function Operation...........................................................12
5-5 Zero Iunction Operation ............................................................13
5-6 Ratio Function Operation..........................................................13
5-7 ZERO-Ratio Function Operation ..............................................15
5-8 Ratio – ZERO Function Operation............................................15
5-9 Sort Function Operation............................................................16
5-10 Comparator Setting and Operation.........................................17
5-11 Manual Data Memory and Read Mode ...................................18
5-12 Auto Datalogging Function......................................................19
5-13 RS232 Communication...........................................................20
5-14 To Disable Auto Power off Function .......................................21

6. BATTERY CHECK-UP 

 REPLACEMENT ..................................21

7. SPECTRAL SENSITIVITY CHARACTERISTIC .............................21

8. MAINTENANCE..............................................................................22

9. RS-232 INTERFACE, SOFTWARE INSTALLATION AND

OPERATION ...................................................................................22

    

Copyright ©

    

2009 TES Electrical Electronic Corp. All rights reserved.

Содержание TES-133


























Отзывы: