manualshive.com logo in svg

Terex Genie Z-80/60, Руководство оператора


Поделиться
Скачать
background image

Fifth Edition • First Printing

 

Operator's Manual

 

 

Transport and Lifting Instructions 

 

 

Part No. 1294418GT 

Z

®

-80/60

 

69

 

 

 

Transport and Lifting Instructions 

 

 

Observe and Obey: 

 

Genie provides this securement information as 
a recommendation. Drivers are solely 
responsible for making sure machines are 
properly secured and the correct trailer is 
selected pursuant to US Department of 
Transportation regulations, other localized 
regulations, and their company policy. 

 

Genie customers needing to containerize any 
lift or Genie product should source a qualified 
freight forwarder with expertise in preparing, 
loading and securing construction and lifting 
equipment for international shipment. 

 

Only qualified mobile elevating work platform 
operators should move the machine on or off 
the truck. 

 

The transport vehicle must be parked on a 
level surface. 

 

The transport vehicle must be secured to 
prevent rolling while the machine is being 
loaded. 

 

Be sure the vehicle capacity, loading surfaces 
and chains or straps are sufficient to withstand 
the machine weight. Genie lifts are very heavy 
relative to their size. See the serial label for 
the machine weight. 

 

 

Be sure the turntable is secured with the 
turntable rotation lock before transporting. Be 
sure to unlock the turntable for operation. 

 

Do not drive the machine on a slope that 
exceeds the uphill, downhill or side slope 
rating. See Driving on a Slope in the Operating 
Instructions section. 

 

If the slope of the transport vehicle bed 
exceeds the maximum slope rating, the 
machine must be loaded and unloaded using a 
winch as described in the brake release 
operation. 

Free-wheel Configuration for 
Winching 

Chock the wheels to prevent the machine from 
rolling. 

Release the circle 
end wheel brakes by 
turning over the drive 
hub disconnect caps. 

 

Be sure the winch 
line is properly 
secured to the drive 
chassis tie points and 
the path is clear of all 
obstructions. 

Reverse the procedures described to re-engage 
the brakes. 

Towing the Genie Z-80/60 is not recommended. If 
the machine must be towed, do not exceed 2 mph 
/ 3.2 km/h. 

Содержание Genie Z-80/60

















































































Отзывы:

Нет отзывов

Похожие инструкции для Genie Z-80/60

Skyjack 213217AAA Operating Manual preview
213217AAA
Бренд: Skyjack Страницы: 112
LGMG A45JE Maintenance Manual preview
A45JE
Бренд: LGMG Страницы: 33
LGMG AR45J Maintenance Manual preview
AR45J
Бренд: LGMG Страницы: 33
LGMG T20J Maintenance Manual preview
T20J
Бренд: LGMG Страницы: 35
LGMG T65J Maintenance Manual preview
T65J
Бренд: LGMG Страницы: 38
LGMG AS0607E Maintenance Manual preview
AS0607E
Бренд: LGMG Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды